Biodegradable Additives

edit

Biodegradable additives are additives that enhance the biodegradation of the polymers by allowing microorganisms to utilize the carbon within the polymer chain itself. Biodegradable additives attract microorgansims to the polymer through quorum sensing after biofilm creation on the plastic product. Additives are generally in masterbatch formation that use carrier resins such as polyethylene, polypropylene, polystyrene or polyethylene terephthalate.

Testing Methods of Biodegradable Additives

edit

ASTM D5511-12 testing is for the "Anerobic Biodegradation of Plastic Materials in a High Solids Environment Under High-Solids Anaerobic-Digestion Conditions"[1]

ASTM D5526-12 testing is for the "Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under Accelerated Landfill Conditions"[2]

ASTM D5210-07 testing is for the "Standard Test Method for Determining the Anaerobic Biodegradation of Plastic Materials in the Presence of Municipal Sewage Sludge"[3]

Laboratories Performing ASTM Testing Methods

edit
  • Eden Research Labs
  • Respirtek
  • NE Laboratories
  • NSF

Biodegradation Process of Biodegradable Additives

edit

A simple chemical equation of the process is: C6H12O6 → 3CO2 + 3CH4

Definition of this process is as follows - In most cases, plastic is made up of hydrophobic polymers. Chains must be broken down into constituent parts for the energy potential to be used by microorganisms. These constituent parts, or monomers, are readily available to other bacteria. The process of breaking these chains and dissolving the smaller molecules into solution is called hydrolysis. Therefore, hydrolysis of these high-molecular-weight polymeric components is the necessary first step in anaerobic biodegradation. Through hydrolysis, the complex organic molecules are broken down into simple sugars, amino acids, and fatty acids.

Acetate and hydrogen produced in the first stages can be used directly by methanogens. Other molecules, such as volatile fatty acids (VFAs) with a chain length greater than that of acetate must first be catabolised into compounds that can be directly used by methanogens.

The biological process of acidogenesis results in further breakdown of the remaining components by acidogenic (fermentative) bacteria. Here, VFAs are created, along with ammonia, carbon dioxide, and hydrogen sulfide, as well as other byproducts. The process of acidogenesis is similar to the way milk sours.

The third stage of anaerobic digestion is acetogenesis. Simple molecules created through the acidogenesis phase are further digested by Acetogens to produce largely acetic acid, as well as carbon dioxide and hydrogen.

The terminal stage of anaerobic biodegradation is the biological process of methanogenesis. Here, methanogens use the intermediate products of the preceding stages and convert them into methane, carbon dioxide, and water. These components make up the majority of the biogas emitted. Methanogenesis is sensitive to both high and low pHs and occurs between pH 6.5 and pH 8. The remaining, indigestible material the microbes cannot use and any dead bacterial remains constitute the digestate.[4]

Biodegradable Additive Manufacturers

edit
  • EcoLogic LLC
  • EcoSafe Plastic
  • BioSphere Plastic[5]
  • ENSO Plastics
  • Bio-tec Environmental[6]

References

edit
  1. ^ "ASTM D5511-12". ASTM International. Retrieved 2012-06-30.
  2. ^ "ASTM D5526-12". ASTM International. Retrieved 2012-06-30.
  3. ^ "ASTM D5210-07". ASTM International. Retrieved 2012-06-30.
  4. ^ "Biodegradation of Plastic by Additives". BioSphere Plastic. Retrieved 2012-08-30.
  5. ^ "Biodegradable Plastic from BioSphere". BioSphere Plastic. Retrieved 2012-08-30.
  6. ^ "Bio-tec Environmental". Bio-tec Environmental. Retrieved 2012-08-30.


GGIwin (talk) 00:08, 31 October 2012 (UTC)Reply

Proposed deletion of BioSphere Plastic

edit
 

The article BioSphere Plastic has been proposed for deletion because of the following concern:

Non-notable company or organization; marginal third-party coverage.

While all contributions to Wikipedia are appreciated, content or articles may be deleted for any of several reasons.

You may prevent the proposed deletion by removing the {{proposed deletion/dated}} notice, but please explain why in your edit summary or on the article's talk page.

Please consider improving the article to address the issues raised. Removing {{proposed deletion/dated}} will stop the proposed deletion process, but other deletion processes exist. In particular, the speedy deletion process can result in deletion without discussion, and articles for deletion allows discussion to reach consensus for deletion. §FreeRangeFrog 23:26, 31 October 2012 (UTC)Reply

  Hello, I'm Materialscientist. I wanted to let you know that I removed an external link you added to the page Plastic , because it seemed to be inappropriate for an encyclopedia. If you think I made a mistake, or if you have any questions, you can leave me a message on my talk page, or take a look at our guidelines about links. Thank you. Materialscientist (talk) 22:58, 11 March 2013 (UTC)Reply

edit

Hi. Thank you for your recent edits. Wikipedia appreciates your help. We noticed though that when you edited Biodegradable bag, you added a link pointing to the disambiguation page Aerobic (check to confirm | fix with Dab solver). Such links are almost always unintended, since a disambiguation page is merely a list of "Did you mean..." article titles. Read the FAQ • Join us at the DPL WikiProject.

It's OK to remove this message. Also, to stop receiving these messages, follow these opt-out instructions. Thanks, DPL bot (talk) 12:51, 12 March 2013 (UTC)Reply