The Dana/Spicer Model 35 is an automotive axle. It has been manufactured by Dana Holding Corporation since 1985 when American Motors (AMC) sold its axle tooling equipment to Dana.[1] The axle was named AMC-15 when it was first made in 1962.[1] Dana upgraded the axle, and added IFS and Twin Traction Beam front axle variations.

Dana 35 from a Jeep

Specifications

edit

The Dana 35 (as well as the AMC-15) is used in many vehicles. The most common applications are as a rear axle in the Jeep Cherokee, Jeep Wrangler, and Jeep Comanche and as a front axle in the Ford Explorer and Ford Ranger. It is "reliable in day-to-day street use, but notoriously the opposite when worked hard."[2]

As the AMC-15 it was used in many AMC cars, most commonly with four and six cylinder engines.

  • Ring Gear: 7.5 inches (191 mm)
  • OEM Inner axle shaft spline count: 27
  • Pinion shaft splines: 26
  • Rear axle ratios: 2.21:1 to 4.88:1[3]
    • TTB axle ratios: 3.07:1 to 4.88:1
    • IFS axle ratios: 3.08:1 to 5:13:1
  • Carrier break: 2.21 - 3.31:1 and 3.55 - 4.88:1
  • Axle Shaft diameter: 1.09 inches (28 mm) (30 Spline)
  • Ring and Pinion gear sets for Jeep Dana 35 rear applications can be used in Ford Ranger IFS (Dana 35) front axles. http://www.4wheelparts.com lists the Spicer gear sets for both versions of this axle as the same part number. [citation needed]

Independent front suspension (IFS) axle

edit

Throughout the 1990s Ford used the Dana 35 as a front axle in both TTB and IFS variations. These units follow Ford's tradition of using high pinion, reverse cut units. Dodge used this front axle for a few years in Dakotas and Durangos.

  • GAWR up to 2900 lbs depending on variation and set up.

Rear solid axle

edit

The Dana 35 is used extensively in Jeeps. This axle had a GAWR up to 2700 lbs.

Gear ratios

edit

Many gear ratios were offered over the axle's lifetime:[4]

Gear Ratios
Ratio:1 Pinion:Ring Teeth
2.21 19:42
2.37 19:45
2.35 17:40
2.53 17:43
2.73 15:41
3.07 14:43
3.08 13:40
3.31 13:43
3.54 13:46
3.58 12:43

DANA 35c

edit

Dana 35c is a newer version of Dana35. C stands for a Custom as the axle was delivered to the end user without axle brackets. The axle uses a C clip, which holds the axle shafts in the carrier. A centre pin locks the shafts in.

Gear Ratio:

3.55 || 11:39 - 4.11 || 9:37 -

Common Applications

edit

Front Axle

edit

The front axle version appeared in:[5]

Dodge

edit
  • 1997-2000 Dakota
  • 1997-2000 Durango

Ford

  • 1989.5-1990 Bronco II TTB
  • 1991-1994 Explorer TTB
  • 1995-2005 Explorer IFS
  • 1990-1997 Ranger TTB
  • 1998-2012 Ranger IFS

Rear Axle

edit

The rear axle version appeared in:[5]

Jeep

edit
  • 1984-1997 Jeep Wagoneer
  • 1984-2001 Jeep Cherokee
  • 1993-2004 Jeep Grand Cherokee
  • 1986-1992 Jeep Comanche
  • 1987-1995 Jeep YJ Wrangler Note: there was no 96 model.
  • 1997-2006 Jeep TJ Wrangler *option Dana 44 rear and Rubicon's had Dana 44's
  • 2007 only some early Jeep JK 2 door Wranglers had Dana 35 non c-clip axles.
  • 2001-2007 Jeep Liberty
  • Dodge Ram Van

References

edit
  1. ^ a b Allen, Jim (2007). Jeep 4x4 Performance Handbook. MotorBooks/MBI Publishing. p. 101. ISBN 978-0-7603-2687-9.
  2. ^ Allen, Jim (2004). Jeep (Collector's Library). MotorBooks/MBI Publishing. p. 179. ISBN 978-0-7603-1979-6. Retrieved 18 April 2013.
  3. ^ "Group 9 Axles -- Propeller Shafts". AMC Eagle Nest. Retrieved 18 April 2013.
  4. ^ AMC 1980 Technical Service Manual. American Motors Corporation. 1980.
  5. ^ a b Incomplete list. Common applications only.