Wikipedia

Crosswalks in North America

Crosswalks in the United States and Canada are normally found at intersections, though sometimes may be found mid-block. Crosswalk installations must follow the regulations specified in the Manual on Uniform Traffic Control Devices (MUTCD).[1] At signalized intersections, crosswalks may have pedestrian signals which display symbols to mandate when pedestrians may cross the street.

A road with white ladder-style markings and a pole with a yellow, diamond-shaped sign upon which is printed the figure of a walking person.
A common-style marked crosswalk with the MUTCD Crosswalk sign

State road rules in the United States usually require a driver to yield the right of way to a pedestrian crossing a road when the pedestrian crosses at a marked crosswalk or an unmarked crosswalk.[2] In some states and cities with jaywalking laws, pedestrians may be restricted from crossing except at a crosswalk and only when the WALK signal is displayed.

Criteria for installation

edit

For crosswalk safety, in the United States there is not much clarity regarding the need for a crosswalk to be marked or unmarked due to the advantages and disadvantages of both approaches, although each city might have its own rules.[3]

Marked crosswalks

edit
 
Crosswalk pavement marking variants per the U.S. FHWA

In the United States, crosswalks are sometimes marked with white stripes, though many municipalities have slightly different methods, styles, or patterns for doing so. The designs used vary widely between jurisdictions, and often vary even between a city and its county (or local equivalents).[1][4] There are two main methods for road markings in the United States, as mandated by the 2009 version of the Manual on Uniform Traffic Control Devices (MUTCD). Most frequently, they are marked with two parallel white lines running from one side of the road to the other, with the width of the lines being typically 12 to 24 inches (300 to 610 mm) wide.[1][4] A third "stop line", which is about the same thickness and extends only across lanes going into the intersection, is usually also present. The stop line acts as the legally mandated stopping point for vehicles, and discourages drivers from stopping in the middle of the crosswalk.[4] The other method involves the use of the more easily visible "continental stripes" (like the UK's zebra crossings), which are sets of multiple bars across the crosswalk itself that are perpendicular to the direction of crossing. These bars are typically 12 to 24 inches (300 to 610 mm) wide and are set 12 to 24 inches (300 to 610 mm) apart. Crosswalks can use a combination of two parallel white lines and continental stripes to create a "ladder" crosswalk, which is highly visible.[1][4]

 
A sign warning motorists to yield to those crossing the crosswalk

Marked crosswalks are usually placed at traffic intersections or crossroads, but are occasionally used at mid-block locations where pedestrian generators are present such as at transit stops, schools, retail, or housing destinations. In the United States, these "mid-block crossings" may include additional regulatory signage such as "PED XING" (for "pedestrian crossing"), flashing yellow beacons, stop or yield signs, or by actuated or automatic signals.[1] Some more innovative crossing treatments include in-pavement flashers, yellow flashing warning lights installed in the roadway, or HAWK beacon—an overhead signal with a pair of red beacons above an amber beacon, when a pedestrian is detected or actuates the device it begins a sequence of amber flashing followed by a solid red, followed by a flashing red phase that allows motorists to proceed, only if the pedestrian(s) are clear of the travel way.[5]

In the United States, crossing laws vary from state to state and sometimes at the local level. All states require vehicles to yield to a pedestrian who has entered a marked crosswalk.[6] Legally speaking, in most states crosswalks exist at all intersections meeting at approximately right angles, whether they are marked or not.[7] All states except Maine and Michigan require vehicles to yield to a pedestrian who has entered an unmarked crosswalk.[6] To gain the right-of-way in some parts of Canada, however, the pedestrian holds out his hand in a position much like that used to shake hands, and steps off the curb.[citation needed] The province of Ontario enacted a law in 2016 that mandates that drivers and bicyclists come to a complete stop at pedestrian "crossovers"—ladder-style crosswalks that are sometimes designated with overhead signs or lights—as well as crosswalks with school crossing guards.[8]

Signalized intersections

edit
See also: Traffic light
 
 
 
Three pedestrian traffic signals in New York City, in three different signal phases:
  • The signal at left displays a "steady upraised hand" signal, which indicates "don't walk".
  • The signal at center displays a "steady walking person" signal, which indicates "walk".
  • The signal at right displays a "flashing upraised hand" signal, which indicates that "don't walk" is imminent. This is accompanied by a countdown timer as per the 2009 MUTCD.

At crossings controlled by signals, generally the poles at both ends of the crosswalk also have the pedestrian signal heads. For many years these bore white walk and Portland Orange dont walk legends,[9] the latter without an apostrophe so that it fits easily on the sign.[10] These colors were selected to provide adequate conspicuity and contrast against the backdrop of red, yellow, and green traffic lights.[11]

Pictograms of an "upraised hand" (symbolizing dont walk) and a "walking person" (symbolizing walk) were made optional in the 1971 version of the MUTCD;[12] the 2000 MUTCD no longer allowed provided an option for word legends,[9] and the Federal Highway Administration officially confirmed[12] that the pictograms are required in the 2009 edition of the MUTCD.[13]

Modern pedestrian signals can be incandescent, neon, fiber-optic, or LED, with the latter three displays typically using less energy.[14]

Regardless of whether pictograms or words are used, the MUTCD defines a steady "upraised hand" or don't walk signal as an indication that a pedestrian cannot enter the street in that signal's direction, while a steady "walking person" or walk indicates that pedestrians can start crossing the street toward that signal.[13] The upraised hand or don't walk signals begin to flash during the pedestrian clearance interval when the transition to the "don't walk" phase of the signal is imminent.[13] This normally occurs several seconds before the light turns yellow, usually going solid orange when the traffic light turns yellow or red; however, the display can be turned into a steady hand or "don't walk" sign while the vehicular light is yellow, or while the vehicular signal is still displaying a green light.[15] In intersections with "leading pedestrian intervals", the upraised hand or "don't walk" sign will continue flashing as the vehicular lights turn red and the other crossing(s) in the intersection display a walking person or "walk" sign. The vehicular traffic is then stopped in all directions for a short period of time before cross traffic is allowed to proceed.[16] The 2009 MUTCD states that the flashing walking person or "walk" signals do not have meaning.[13] The "flashing walk" indication was formerly used to delineate "watch out for turning vehicles"[17] and is still in use in Washington, D.C.;[18] however, as of the 2003 MUTCD, this was replaced by an optional "animated eyes" indication within the pedestrian signal display,[19][20] which was placed in the MUTCD following a study that recommended the usage of the "animated eyes" signal.[21]

A gridded "egg-crate visor" (U.S. patent 3,863,251) is customarily placed in front of the lights to shield them from the sun and increase their visibility, but such visors can also be vulnerable to snow or ice accumulation on the screens, which in turn could block the pedestrian display.[14] Pedestrian signals can also use a triangular-prism-shaped "cutaway visor" or "cap visor" (so named because the pitch of the visor, is shaped like a baseball cap), which mainly covers the top of the signal and the tops of the left and right sides; or a more rectangular-shaped "tunnel visor", which fully covers the left, right, and top sides of the pedestrian display.[22][23]

 
Three-state signal sequence with textual messages typical for the United States; words may be replaced by symbols.

In some cities in the US, other methods of pedestrian detection are being or have been tested, including infrared and microwave technology, as well as weight sensors built in at curbside.[24] A 2000 study of these detectors in Los Angeles, Phoenix, and Rochester found that the infrared and microwave technologies both helped reduce conflicts between pedestrians and turning vehicles, as well as pedestrians starting during the "don't walk" phase.[25][26]: 38–39  Subsequent studies found that the efficacy of these sensors varied based on pedestrian traffic at the location where they were installed.[26]: 39–40 

On fully actuated signals, or semi-actuated traffic signals, pressing the button to cross a smaller side street will cause an "instant walk signal". In most states, drivers only have to wait until the pedestrian has finished crossing the half of the crosswalk that the driver is driving on, after which the driver may proceed.[citation needed] However, in some states (such as Utah[27]), if the driver is in a school zone with the lights flashing, the driver must wait until the entire crosswalk is clear before he may proceed.[citation needed]

Massachusetts allows an unusual indication variation for pedestrian movement. At signalized intersections without separate pedestrian signal heads, the traffic signals may be programmed to turn red in all directions, followed by a steady display of yellow lights simultaneously with the red indications. During this red-plus-yellow indication, the intersection is closed to vehicular traffic and pedestrians are given an "exclusive pedestrian interval", or a pedestrian scramble phase, in which they can cross any leg of the intersection, usually in whatever direction they choose.[28] This replaces the extra pedestrian signal, but is in violation of the 2009 MUTCD.[13] This practice is obsolescent but it remains in the Commonwealth's driver's manual.[28]

Jaywalking

edit
Further information: Jaywalking § Canada, and Jaywalking § United States

Jaywalking is a term which refers to the act of crossing the road other than at a crosswalk or against the crosswalk signal. Jaywalking might be understood as walking against a pedestrian walk signal; crossing a street where there is no crosswalk (midblock crossing); crossing a street outside of a marked crosswalk where one is present; and walking on a street along with the traffic flow (ignoring designated pedestrian pathways).[29]

Jaywalking is an offence in many cities, U.S. states and Canadian provinces, although prohibitions vary from jurisdiction to jurisdiction.[30][31] Nonetheless, jaywalking remains the cultural norm in some cities such as New York and Toronto.[32]: 216, 222, 224 [30] 'Jaywalking' is recorded in the Oxford English Dictionary from 1917. According to historian and alternative transportation advocate Peter D. Norton, the word was promoted by pro-automobile interests in the 1920s.[33] Jaywalking laws in the United States have been criticized due to racial bias in enforcement.[34]

References

edit
  1. ^ a b c d e "Part II of II: Best Practices Design Guide – Sidewalk2". Federal Highway Administration. Retrieved March 10, 2017.
  2. ^ "Hit By a Car: Pedestrian Accidents in Florida | South Florida Personal Injury & Car Accident Blog". southfloridainjuryaccidentblog.com. December 11, 2014. Retrieved February 10, 2018.[self-published source]
  3. ^ Safety and Guidelines for Marked and Unmarked Pedestrian Crosswalks at Unsignalized Intersections in Nevada (Report). Nevada Department of Transportation. 2012.
  4. ^ a b c d "Chapter 3B". Manual on Uniform Traffic Control Devices (2009 ed.). 2009. Retrieved March 10, 2017.
  5. ^ "Chapter 4F". Manual on Uniform Traffic Control Devices (2009 ed.). 2009. Retrieved March 10, 2017.
  6. ^ a b "Right of Way in the Crosswalk" (PDF). Archived from the original (PDF) on July 29, 2014.
  7. ^ See here (discussing the Uniform Vehicle Code and stating that "a crosswalk at an intersection is defined as the extension of the sidewalk or the shoulder across the intersection, regardless of whether it is marked or not."); see also California Vehicle Code section 275(a) ("'Crosswalk' is . . . [t]hat portion of a roadway included within the [extension] of the boundary lines of sidewalks at intersections where the intersecting roadways meet at approximately right angles, except the [extension] of such lines from an alley across a street")
  8. ^ "What is the new crosswalk law in Ontario and what's the reason for it?". The Globe and Mail. January 26, 2016. Retrieved March 10, 2017.
  9. ^ a b "Part 4: Traffic Signals" (PDF). Manual on Uniform Traffic Control Devices (2000 ed.). December 2000. pp. 4E1 to 4E14. Retrieved March 9, 2017.
  10. ^ Smallwood, Karl (July 21, 2014). "Why No One Bothers Putting Apostrophes in 'Don't Walk' Signs". Gizmodo. Retrieved March 10, 2017.
  11. ^ Levinson, David (September 24, 2015). "Why is the Walking Man White?". Retrieved April 21, 2021.
  12. ^ a b Kaufman, David (July 6, 2020). "The Unintentional Racism Found in Traffic Signals". Retrieved April 21, 2021.
  13. ^ a b c d e "Chapter 4E". Manual on Uniform Traffic Control Devices (2009 ed.). 2009. Retrieved March 9, 2017.
  14. ^ a b Yauch, Peter J. (January 1, 1990). Traffic Signal Control Equipment: State of the Art. Transportation Research Board. p. 43. ISBN 9780309049177.
  15. ^ "Figure 4E-2 Long Description". Manual on Uniform Traffic Control Devices (2009 ed.). Retrieved March 9, 2017.
  16. ^ Houten, Ron; Retting, Richard; Farmer, Charles; Houten, Joy (January 1, 2000). "Field Evaluation of a Leading Pedestrian Interval Signal Phase at Three Urban Intersections". Transportation Research Record: Journal of the Transportation Research Board. 1734: 86–92. doi:10.3141/1734-13. ISSN 0361-1981. S2CID 111010659.
  17. ^ Olson, P.L.; Dewar, R.E. (2002). Human Factors in Traffic Safety. Lawyers & Judges Pub. ISBN 978-0-913875-47-6. Retrieved March 12, 2017.
  18. ^ Raschke, Kurt (November 12, 2010). "'Walking person' confusion". Kurt Raschke – Technologist. Archived from the original on March 12, 2017. Retrieved March 12, 2017.
  19. ^ "Chapter 4E". Manual on Uniform Traffic Control Devices (2003 ed.). Retrieved March 9, 2017.
  20. ^ Redmon, Tamara (November–December 2005). "Looking Out for Pedestrians". Federal Highway Administration. FHWA-HRT-05-001 Vol. 69 No. 3. Retrieved March 12, 2017.
  21. ^ Van Houten, R. (2001). "Animated LED 'Eyes' Traffic Signals" (PDF). ITS-IDEA Program Project Final Report.
  22. ^ "History of Traffic Signal Visors". www.kbrhorse.net. Retrieved March 10, 2017.
  23. ^ "Pedestrian Signals". www.signalfan.com. Retrieved March 10, 2017.
  24. ^ "Automated Pedestrian Detection". Pedestrian and Bicycle Information Center. Retrieved March 13, 2017.
  25. ^ Hughes, R.; Huang, H.; Zegeer, C.; Cynecki, M. (2001). Evaluation of Automated Pedestrian Detection at Signalized Intersections (PDF) (Report). Federal Highway Administration. Archived from the original (PDF) on May 9, 2006. Retrieved March 13, 2017.
  26. ^ a b Mead, Jill; Zegeer, Charlie; Bushell, Max (April 2014). "Evaluation of Pedestrian-Related Roadway Measures: A Summary of Available Research" (PDF). Pedestrian and Bicycle Information Center.
  27. ^ "Title 41 Chapter 6a Part 10 Section 1002". Utah State Legislature. Retrieved March 13, 2017.
  28. ^ a b Massachusetts Department of Transportation, Registry of Motor Vehicles Division (c. 2015). Driver's Manual (PDF). p. 82. Archived from the original (PDF) on February 15, 2017. Retrieved March 10, 2017. You must yield to pedestrians if your traffic signal is red or if it is red and yellow.
  29. ^ Heinonen, Justin A.; Eck, John E. (2007). "Pedestrian Injuries & Fatalities". ASU Center for Problem-Oriented Policing.
  30. ^ a b Ellison, Marc (September 5, 2013). "Data Shows Torontonians Love to Jaywalk — And Sometimes Pay the Price". The Toronto Star. Retrieved April 8, 2016.
  31. ^ McManus, Marna (November 25, 2018). "Is Jaywalking Considered a Traffic Violation in Weyburn". www.discoverweyburn.com. Golden West Broadcasting. Retrieved June 24, 2020.
  32. ^ Vanderbilt, Tom (2008). Traffic: Why We Drive the Way We Do (And What It Says About Us). New York: Alfred A Knopf. ISBN 978-0-307-26478-7.
  33. ^ Vanderbilt, Tom (November 2, 2009). "In Defense of Jaywalking". Slate Magazine. Retrieved May 27, 2022.
  34. ^ Chow, Vivian (October 1, 2022). "New law allows Californians to legally jaywalk". KTLA. Retrieved October 1, 2022.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Crosswalks_in_North_America&oldid=1238656131"