Concrete cone is one of the failure modes of anchors in concrete, loaded by a tensile force. The failure is governed by crack growth in concrete, which forms a typical cone shape having the anchor's axis as revolution axis.

Concrete Cone Model[1]

Mechanical models

edit

ACI 349-85

edit

Under tension loading, the concrete cone failure surface has 45° inclination. A constant distribution of tensile stresses is then assumed. The concrete cone failure load   of a single anchor in uncracked concrete unaffected by edge influences or overlapping cones of neighboring anchors is given by:[2]

 

Where:

  - tensile strength of concrete

  - Cone's projected area

Concrete capacity design (CCD) approach for fastening to concrete

edit

Under tension loading, the concrete capacity of a single anchor is calculated assuming an inclination between the failure surface and surface of the concrete member of about 35°. The concrete cone failure load   of a single anchor in uncracked concrete unaffected by edge influences or overlapping cones of neighboring anchors is given by:[2]

 ,

Where:

  - 13.5 for post-installed fasteners, 15.5 for cast-in-site fasteners

  - Concrete compressive strength measured on cubes [MPa]

  - Embedment depth of the anchor [mm]

The model is based on fracture mechanics theory and takes into account the size effect, particularly for the factor   which differentiates from   expected from the first model. In the case of concrete tensile failure with increasing member size, the failure load increases less than the available failure surface; that means the nominal stress at failure (peak load divided by failure area) decreases.[3]

 
Overlapping Areas in case of group of anchors[1]

Current codes take into account a reduction of the theoretical concrete cone capacity   considering: (i) the presence of edges; (ii) the overlapping cones due to group effect; (iii) the presence of an eccentricity of the tension load.[4]

Difference between models

edit

The tension failure loads predicted by the CCD method fits experimental results over a wide range of embedment depth (e.g. 100 – 600 mm).[2] Anchor load bearing capacity provided by ACI 349 does not consider size effect , thus an underestimated value for the load-carrying capacity is obtained for large embedment depths.[2]

Influence of the head size

edit

For large head size, the bearing pressure in the bearing zone diminishes. An increase of the anchor's load-carrying capacity is observed . Different modification factors were proposed in technical literature.[5][6]

Un-cracked and cracked concrete

edit

Anchors, experimentally show a lower load-bearing capacity when installed in a cracked concrete member. The reduction is up to 40% with respect to the un-cracked condition, depending on the crack width.[7] The reduction is due to the impossibility to transfer both normal and tangential stresses at the crack plane.

References

edit
  1. ^ a b Cook, Ronald; Doerr, G T; Klingner, R.E. (2010). Design Guide For Steel To Concrete Connections. University Of Texas Austin.
  2. ^ a b c d Fuchs, Werner; Eligehausen, Rolf (1995). "Concrete Capacity Design (CCD) Approach for Fastening to Concrete". ACI Structural Journal. 109 (January): 1–4. ISSN 0889-3241.
  3. ^ Ožbolt, Joško; Eligehausen, Rolf; Reinhardt, Hans-Wolf (1999). "Size effect on the concrete cone pull-out load". International Journal of Fracture. 95: 391–404. ISSN 0376-9429.
  4. ^ ACI (2004). "ACI 349.2 Guide to the Concrete Capacity Design ( CCD ) Method — Embedment Design Examples". Concrete (Ccd): 1–77.
  5. ^ Ožbolt, Joško; Eligehausen, Rolf; Periškić, G.; Mayer, U. (2007). "3D FE analysis of anchor bolts with large embedment depths". Engineering Fracture Mechanics. 74 (1–2): 168–178. doi:10.1016/j.engfracmech.2006.01.019. ISSN 0013-7944.
  6. ^ Nilforoush, R.; Nilsson, M.; Elfgren, L.; Ožbolt, J.; Hofmann, J.; Eligehausen, R. (2017). "Tensile capacity of anchor bolts in uncracked concrete: Influence of member thickness and anchor's head size". ACI Structural Journal. 114 (6): 1519–1530. doi:10.14359/51689503. ISSN 0889-3241.
  7. ^ Mallèe, Rainer; Eligehausen, Rolf; Silva, John F (2006). Anchors In Concrete Structures. Ernst&Shon. ISBN 978-3433011430.

See also

edit