Wikipedia

Anion exchange membrane electrolysis

Anion exchange membrane (AEM) electrolysis is the electrolysis of water that utilises a semipermeable membrane that conducts hydroxide ions (OH−) called an anion exchange membrane. Like a proton-exchange membrane (PEM), the membrane separates the products, provides electrical insulation between electrodes, and conducts ions. Unlike PEM, AEM conducts hydroxide ions. The major advantage of AEM water electrolysis is that a high-cost noble metal catalyst is not required, low-cost transition metal catalyst can be used instead.[1][2] AEM electrolysis is similar to alkaline water electrolysis, which uses a non-ion-selective separator instead of an anion-exchange membrane.

AEM electrolysis
AEM water electrolysis working principle with HER and OER.

Advantages and Challenges

edit

Advantages

edit

Of all water electrolysis methods, AEM electrolysis can combine the advantages of alkaline water electrolysis (AWE) and PEM electrolysis.[3][4] Polymer electrolyte membrane electrolysis uses expensive platinum-group metals (PGMs) such as platinum, iridium, and ruthenium as a catalyst. Iridium, for instance, is more scarce than platinum; a 100 MW PEM electrolyser is expected to require 150 kg of Iridium, which will cost an estimated 7 million USD.[5] Like alkaline water electrolysis, electrodes in AEM electrolysis operate in an alkaline environment, which allows non-noble, low-cost catalysts based on Ni, Fe, Co, Mn, Cu, etc to be used.[1][3][4][6][7]

AEM electrolyser can run on pure water or slightly alkaline solutions (0.1-1M KOH/NaOH) unlike highly concentrated alkaline solutions (5M KOH/NaOH) in AWE.[3][8] This reduces the risk of leakage.[3] Using an alkaline solution, usually KOH/NaOH increases membrane conductivity and adds a hydroxide ion conductive pathway, which increases the utilisation of catalyst. The current density of an AEM electrolyser without a PGM catalyst operating at 1 A/cm2 was reported to require 1.8 volts and 1.57 volts in pure water-fed and 1 M KOH-fed, respectively.[9] Electrolyte can be fed on both anode and cathode side or anode side only.[10]

In the zero-gap design of AWE, the electrodes are separated only by a diaphragm which separates the gases. The diaphragm only allows water and hydroxide ions to pass through, but does not completely eliminate gas cross-over. Oxygen gas can enter the hydrogen half-cell and react on the cathode side to form water, which reduces the efficiency of the cell. Gas cross-over from the H2 to the O2 evolution side can pose a safety hazard because it can create an explosive gas mixture with >4%mol H2.[8] [11] The AEM electrolyser was reported to maintain H2 crossover to less than 0.4% for the 5000 h of operation.[12]

AEM based on an aromatic polymer backbone is promising due to its significant cost reduction. Compare to Nafion membrane use in PEM, the production of Nafion required highly toxic chemicals, which increased the cost (>1000$/m2)[13][14] and fluorocarbon gas is produced at the production stage of tetrafluoroethylene, which poses a strong environmental impact.[15] Fluorinated raw materials are inessential for AEM, allowing for a wider selection of low-cost polymer chemistry.[2]

Challenges

edit
 
Degraded AEM Fumatech FAA3-PK-75 after mechanical strength testing to evaluate the mechanical properties of the membrane.[16]

AEM electrolysis is still in the early research and development stage, while alkaline water electrolysis is in the mature stage and PEM electrolysis is in the commercial stage. There is less academic literature on pure-water fed AEM electrolysers compared to the usage of KOH solution.[11] The major technical challenge facing a consumer level AEM electrolyser is the low durability of the membrane, which refers to the short device lifetime or longevity. The lifetimes of PEM electrolyser stacks range from 20,000 h to 80,000 h.[9][8] Literature surveys have found that AEM electrolyser durability is demonstrated to be >2000 h, >12,000 h, and >700 h for pure water-fed (Pt group catalyst on anode and cathode), concentrated KOH-fed, and 1wt% K2CO3-fed respectively.[9]

To overcome the obstacles for a large scale usage of AEM, increasing ionic conductivity and durability is essential. Many AEM breakdown at temperatures higher than 60°C, AEM that can tolerate the presence of O2, high pH, and temperatures exceeding 60°C are needed.[17][18]

Science

edit

Reactions

edit

Oxygen evolution reactions (OER) need four electrons to produce one molecule of O2, consume multiple OH- anions, and form multiple adsorbed intermediates on the surface of the catalyst. These multiple steps of reaction create a high energy barrier and thus a high overpotential, which causes the OER to be sluggish. The performance of the AEM electrolyser largely depends on OER. The overpotential of OER can be reduced with an efficient catalyst that breaks the reaction's intermediate bond. Hydrogen evolution reaction (HER) kinetics in alkaline solutions are slower than in acidic solutions because of additional proton dissociation and the formation of hydrogen intermediate (H*) that is not present in acidic conditions.[17][3]

Anode reaction

edit
   
   
   
   

Where the * indicate species adsorbed to the surface of the catalyst.

Cathode reaction

edit

The reaction starts with water adsorption and dissociation in Volmer step and either hydrogen desorption in the Tafel step or Heyrovsky step.

Volmer step:    
Tafel step:    

Heyrovsky step:  

 

Anion exchange membrane

edit
Further information: Anion exchange membrane

Hydroxide ion intrinsically has lower mobility than H+, increasing ion exchange capacity can compensate for this lower mobility but also increase swelling and reduce membrane mechanical stability. Cross-linking membranes can compensate for membrane mechanical instability. The quaternary ammonium (QA) headgroup is commonly employed to attach polymer matrices in AEM. The head group allows anions but not cations to be transported. QA AEMs have low chemical stability because they are susceptible to OH- attack. Promising head group candidates include imidazolium-based head group and nitrogen-free head groups such as phosphonium, sulphonium, and ligand-metal complex. Most QAs and imidazolium groups degrade in alkaline environments by Hofmann degradation, SN2 reaction, or ring-opening reaction, especially at high temperatures and pH.[17][19]

Polymeric AEM backbones are cationic-free base polymers. Poly(arylene ether)-based backbones, polyolefin-based backbones, polyphenylene-based backbones, and backbones containing cationic moieties are some examples. [17]

Some of the best-performing AEMs are HTMA-DAPP, QPC-TMA, m-PBI, and PFTP.[15]

Membrane electrode assembly

edit

A membrane electrode assembly (MEA) is made of an anode and cathode catalyst layer with a membrane layer in between. The catalyst layer can be deposited on the membrane or the substrate. Catalyst-coated substrate (CCS) and catalyst-coated membrane (CCM) are two approaches to preparing MEA. A substrate must conduct electricity, support the catalyst mechanically, and remove gaseous products.

Nickel is typically used as a substrate for AEM, while titanium is for PEM; both nickel and titanium can be used on AEM. Carbon materials are not suitable for the anode side because of their degradation by HO- ions, which are nucleophiles.[11] On the cathode, nickel, titanium, and carbon can be readily used. The catalyst layer is typically made by mixing catalyst powder and ionomer to produce an ink or slurry that is applied by spraying or painting. [17][11] Other methods include electrodeposition, magnetron sputtering, chemical electroless plating, and screen printing onto the substrate. [11][20]

Ionomers act as a binder for the catalyst, substrate support, and membrane, which also provide OH- conducting ions and increase electrocatalytic activities. [4][17][11]

See also

edit

References

edit
  1. ^ a b Varcoe, John R.; Atanassov, Plamen; Dekel, Dario R.; Herring, Andrew M.; Hickner, Michael A.; Kohl, Paul. A.; Kucernak, Anthony R.; Mustain, William E.; Nijmeijer, Kitty; Scott, Keith; Xu, Tongwen; Zhuang, Lin (2014). "Anion-exchange membranes in electrochemical energy systems". Energy Environ. Sci. 7 (10): 3135–3191. doi:10.1039/C4EE01303D. hdl:10044/1/24509.
  2. ^ a b Dekel, Dario R. (January 2018). "Review of cell performance in anion exchange membrane fuel cells". Journal of Power Sources. 375: 158–169. Bibcode:2018JPS...375..158D. doi:10.1016/j.jpowsour.2017.07.117.
  3. ^ a b c d e Yang, Juchan; Jang, Myeong Je; Zeng, Xiaojun; Park, Yoo Sei; Lee, Jooyoung; Choi, Sung Mook; Yin, Yadong (October 2021). "Non-precious electrocatalysts for oxygen evolution reaction in anion exchange membrane water electrolysis: A mini review". Electrochemistry Communications. 131: 107118. doi:10.1016/j.elecom.2021.107118.
  4. ^ a b c Shirvanian, Paige; Loh, Adeline; Sluijter, Soraya; Li, Xiaohong (November 2021). "Novel components in anion exchange membrane water electrolyzers (AEMWE's): Status, challenges and future needs. A mini review". Electrochemistry Communications. 132: 107140. doi:10.1016/j.elecom.2021.107140. hdl:10871/127974. S2CID 240613300.
  5. ^ Henkensmeier, Dirk; Najibah, Malikah; Harms, Corinna; Žitka, Jan; Hnát, Jaromír; Bouzek, Karel (1 May 2021). "Overview: State-of-the Art Commercial Membranes for Anion Exchange Membrane Water Electrolysis". Journal of Electrochemical Energy Conversion and Storage. 18 (2). doi:10.1115/1.4047963.
  6. ^ Xu, Qiucheng; Zhang, Liyue; Zhang, Jiahao; Wang, Jingyu; Hu, Yanjie; Jiang, Hao; Li, Chunzhong (September 2022). "Anion Exchange Membrane Water Electrolyzer: Electrode Design, Lab-Scaled Testing System and Performance Evaluation" (PDF). EnergyChem. 4 (5): 100087. doi:10.1016/j.enchem.2022.100087. S2CID 251354531.
  7. ^ Lindquist, Grace A.; Xu, Qiucheng; Oener, Sebastian Z.; Boettcher, Shannon W. (December 2020). "Membrane Electrolyzers for Impure-Water Splitting". Joule. 4 (12): 2549–2561. doi:10.1016/j.joule.2020.09.020.
  8. ^ a b c Shiva Kumar, S.; Lim, Hankwon (November 2022). "An overview of water electrolysis technologies for green hydrogen production". Energy Reports. 8: 13793–13813. doi:10.1016/j.egyr.2022.10.127.
  9. ^ a b c Li, Dongguo; Motz, Andrew R.; Bae, Chulsung; Fujimoto, Cy; Yang, Gaoqiang; Zhang, Feng-Yuan; Ayers, Katherine E.; Kim, Yu Seung (2021). "Durability of anion exchange membrane water electrolyzers". Energy & Environmental Science. 14 (6): 3393–3419. doi:10.1039/d0ee04086j.
  10. ^ Xu, Dongyu; Stevens, Michaela Burke; Cosby, Monty R.; Oener, Sebastian Z.; Smith, Adam M.; Enman, Lisa J.; Ayers, Katherine E.; Capuano, Christopher B.; Renner, Julie N.; Danilovic, Nemanja; Li, Yaogang; Wang, Hongzhi; Zhang, Qinghong; Boettcher, Shannon W. (4 January 2019). "Earth-Abundant Oxygen Electrocatalysts for Alkaline Anion-Exchange-Membrane Water Electrolysis: Effects of Catalyst Conductivity and Comparison with Performance in Three-Electrode Cells". ACS Catalysis. 9 (1): 7–15. doi:10.1021/acscatal.8b04001. S2CID 105391723.
  11. ^ a b c d e f Miller, Hamish Andrew; Bouzek, Karel; Hnat, Jaromir; Loos, Stefan; Bernäcker, Christian Immanuel; Weißgärber, Thomas; Röntzsch, Lars; Meier-Haack, Jochen (2020). "Green hydrogen from anion exchange membrane water electrolysis: a review of recent developments in critical materials and operating conditions". Sustainable Energy & Fuels. 4 (5): 2114–2133. doi:10.1039/c9se01240k.
  12. ^ Moreno-González, Marta; Mardle, Peter; Zhu, Shan; Gholamkhass, Bobak; Jones, Scot; Chen, Nathan; Britton, Benjamin; Holdcroft, Steven (January 2023). "One year operation of an anion exchange membrane water electrolyzer utilizing Aemion+® membrane: Minimal degradation, low H2 crossover and high efficiency". Journal of Power Sources Advances. 19: 100109. doi:10.1016/j.powera.2023.100109.
  13. ^ Mamlouk, Mohamed (2022). "Alkaline Anion Exchange Membrane (AEM) Water Electrolysers—Current/Future Perspectives in Electrolysers for Hydrogen". Comprehensive Renewable Energy: 473–504. doi:10.1016/B978-0-12-819727-1.00103-5. ISBN 9780128197349. S2CID 239231605.
  14. ^ Khomein, Piyachai; Ketelaars, Wesley; Lap, Tijs; Liu, Gao (March 2021). "Sulfonated aromatic polymer as a future proton exchange membrane: A review of sulfonation and crosslinking methods". Renewable and Sustainable Energy Reviews. 137: 110471. doi:10.1016/j.rser.2020.110471. S2CID 228845451.
  15. ^ a b Santoro, Carlo; Lavacchi, Alessandro; Mustarelli, Piercarlo; Di Noto, Vito; Elbaz, Lior; Dekel, Dario R.; Jaouen, Frédéric (22 April 2022). "What is Next in Anion-Exchange Membrane Water Electrolyzers? Bottlenecks, Benefits, and Future". ChemSusChem. 15 (8): e202200027. Bibcode:2022ChSCh..15E0027S. doi:10.1002/cssc.202200027. hdl:10281/380104. PMC 9310600. PMID 35263034.
  16. ^ Najibah, Malikah; Tsoy, Ekaterina; Khalid, Hamza; Chen, Yongfang; Li, Qingfeng; Bae, Chulsung; Hnát, Jaromír; Plevová, Michaela; Bouzek, Karel; Jang, Jong Hyun; Park, Hyun S.; Henkensmeier, Dirk (December 2021). "PBI nanofiber mat-reinforced anion exchange membranes with covalently linked interfaces for use in water electrolysers". Journal of Membrane Science. 640: 119832. doi:10.1016/j.memsci.2021.119832. S2CID 239639812.
  17. ^ a b c d e f Du, Naiying; Roy, Claudie; Peach, Retha; Turnbull, Matthew; Thiele, Simon; Bock, Christina (13 July 2022). "Anion-Exchange Membrane Water Electrolyzers". Chemical Reviews. 122 (13): 11830–11895. doi:10.1021/acs.chemrev.1c00854. PMC 9284563. PMID 35442645.
  18. ^ Chand, Kishore; Paladino, Ombretta (February 2023). "Recent developments of membranes and electrocatalysts for the hydrogen production by anion exchange membrane water electrolysers: A review". Arabian Journal of Chemistry. 16 (2): 104451. doi:10.1016/j.arabjc.2022.104451. hdl:11567/1101845. S2CID 254002110.
  19. ^ Hagesteijn, Kimberly F. L.; Jiang, Shanxue; Ladewig, Bradley P. (August 2018). "A review of the synthesis and characterization of anion exchange membranes". Journal of Materials Science. 53 (16): 11131–11150. Bibcode:2018JMatS..5311131H. doi:10.1007/s10853-018-2409-y. hdl:10044/1/60973. S2CID 139833074.
  20. ^ López-Fernández, Ester; Sacedón, Celia Gómez; Gil-Rostra, Jorge; Yubero, Francisco; González-Elipe, Agustín R.; de Lucas-Consuegra, Antonio (20 October 2021). "Recent Advances in Alkaline Exchange Membrane Water Electrolysis and Electrode Manufacturing". Molecules. 26 (21): 6326. doi:10.3390/molecules26216326. hdl:10261/256196. PMC 8587517. PMID 34770735.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Anion_exchange_membrane_electrolysis&oldid=1226300316"