Waste weir

(Redirected from Waste Weir)

A waste weir on a navigable canal is a slatted gate on each canal level or pound, to remove excess water and to drain the canal for repairs or for the winter shutdown.[1] This differs for a dam or reservoir, for which a waste weir is another name for a spillway, i.e. not having the boards to adjust the water height nor the paddles to drain all the water as on a canal, only to drain the excess.

Uses

edit
Example of a waste weir to regulate water level. (Looking from above)
Paddle valves closed, and boards put in. Topmost board determines height of water in pound.
Same waste weir with valves open and boards taken out, to drain canal prism.

A canal will often need some means to maintain a water level. A canal constantly consumes water due to leakage, evaporation, and the operation of lift locks. Nevertheless, excess water from storms or emptying locks [2] could cause problems by eroding the banks of a canal, causing washouts, and flooding buildings or adjacent properties. Waste weirs were one of several measures used to remove surplus water. The waste weir also functioned as an opening to drain the entire canal prism of water for repairs, or for winter (to avoid damage from freezing water), or in anticipation of flooding.[3][4]

 
Morris Canal Overflow and Waste Weir site

In some cases when a creek was used to feed the canal, a waste weir was necessary for excess water from the creek. For instance, on the Morris Canal, the Lopatcong Creek went into the canal to feed it, but it had a tendency to flood, hence the need for a couple of waste weirs in the area around the bottom of Inclined Plane 9 West near Port Warren, New Jersey (near Strykers Road today).[5]

Reservoirs and tanks also use a waste weir for flood discharges.[6]

Design

edit
 
Engineering drawing of a waste weir from the Chesapeake and Ohio Canal

The maximum flow output   in cubic meters/sec over the top of the waste weir with a length   and height of water   above the crest can be calculated by the formulas:

 

and

 

where g=gravitational constant of   and Cd is the coefficient of discharge over the weir. [7] Various values of Cd can be given as follows:[8]

Crest type  
Weir with crest up to one meter in width 0.625
Weir with crest greater than one meter in width 0.562
Rough stone sloping escape 0.500
Flush escape (no drop) 0.437

Construction

edit

Construction methods varied depending on the canal. On the Erie Canal and the Chesapeake and Ohio Canal, waste weirs were often constructed from masonry or concrete.

Since a waste weir was part of canal property, it would sometimes be explicitly protected by law. On the Morris Canal, New Jersey Statue 136 section 61 stated that for willfully and maliciously opening the gates of waste weirs the penalty was $25.[9]

edit

References

edit
  1. ^ Kytle, Elizabeth (1983). Home on the Canal. Cabin John, MD: Seven Locks Press. ISBN 978-080185328-9., p. 272-273
  2. ^ For instance, a lock on the Chesapeake and Ohio Canal was typically 15 feet wide, 95 feet long, and with an 8-foot lift requires 11400 cubic feet or 85,000 gallons to fill. These are small compared to locks on modern canals such as the Panama canal.
  3. ^ "The Waste Weir". Union College. Retrieved 2013-10-06.
  4. ^ "The Waste Weir". The Erie Canal Village. Retrieved 2013-10-06.
  5. ^ "Unknown" (PDF).[permanent dead link]
  6. ^ Bligh, William George (1907). The Practical Design of Irrigation Works. D. Van Nostrand. pp. 335.
  7. ^ Challa, Satya Narayana Murthy (2009). Water Resources Engineering: Principles and Practice. New Age International Pvt Ltd Publishers. p. 52. ISBN 978-8122413823.
  8. ^ Challa, p. 47
  9. ^ Jersey, New (1911). Compiled Statutes of New Jersey: intoxication liquors - replevin. Soney & Sage.