Spatial multiplexing

(Redirected from Spatial Multiplexing)

Spatial multiplexing or space-division multiplexing (SM, SDM or SMX) is a multiplexing technique in MIMO wireless communication, fiber-optic communication and other communications technologies used to transmit independent channels separated in space.

Spatial multiplexing
2xSMX or STC+2xMRC

Fiber-optic communication

edit

In fiber-optic communication SDM refers to the usage of the transverse dimension of the fiber to separate the channels.

Techniques

edit

Multi-core fiber (MCF)

edit

Multi-core fibers are designed with more than a single core. Different types of MCFs exist, of which “Uncoupled MCF” is the most common, in which each core is treated as an independent optical path. The main limitation of these systems is the presence of inter-core crosstalk. In recent times, different splicing techniques, and coupling methods have been proposed and demonstrated, and despite many of the component technologies still being in the development stage, MCF systems already present the capability for huge transmission capacity.[citation needed]

Recently, some developed component technologies for multicore optical fiber have been demonstrated, such as three-dimensional Y-splitters between different multicore fibers,[1] a universal interconnection among the same fiber cores,[2] and a device for fast swapping and interchange of wavelength-division multiplexed data among cores of multicore optical fiber.[3]

Multi-mode fibers (MMF) and Few-mode fibers (FMF)

edit

Multi-mode fibers have a larger core that allows the propagation of multiple cylindrical transverse modes (Also referred as linearly polarized modes), in contrast to a single mode fiber (SMF) that only supports the fundamental mode. Each transverse mode is spatially orthogonal, and allows for the propagation in both orthogonal polarization.

Typical MMF are currently not viable for SDM, as the high mode count results in unmanageable levels of modal coupling and dispersion. The utilization of few-mode fibers, which are MMFs with a core size designed specially to allow a low count of spatial modes, is currently under consideration.

Due to physical imperfections, the modes exchange power and are experience different effective refractive indexes as they propagate through the fiber.[4] The power exchange results in modal coupling, and this effect is known to reduce the achievable capacity of the fiber,[5] if the modes experience unequal gain or attenuation. Therefore, if not compensated, the capacity increase is not linear to the mode count. The effective refractive index difference results in inter-symbolic interference, resulting from delay spread.[6]

Mode multiplexers consist of photonic lanterns, multi-plane light conversion, and others.

Fiber bundles

edit

Bundled fibers are also considered a form of SDM.

Wireless communications

edit

If the transmitter is equipped with   antennas and the receiver has   antennas, the maximum spatial multiplexing order (the number of streams) is,

 

if a linear receiver is used. This means that   streams can be transmitted in parallel, ideally leading to an   increase of the spectral efficiency (the number of bits per second per Hz that can be transmitted over the wireless channel). The practical multiplexing gain can be limited by spatial correlation, which means that some of the parallel streams may have very weak channel gains.

Encoding

edit

Open-loop approach

edit

In an open-loop MIMO system with   transmitter antennas and   receiver antennas, the input-output relationship can be described as

 

where   is the   vector of transmitted symbols,   are the   vectors of received symbols and noise respectively and   is the   matrix of channel coefficients. An often encountered problem in open loop spatial multiplexing is to guard against instance of high channel correlation and strong power imbalances between the multiple streams. One such extension which is being considered for DVB-NGH systems is the so-called enhanced Spatial Multiplexing (eSM) scheme.

Closed-loop approach

edit

A closed-loop MIMO system utilizes Channel State Information (CSI) at the transmitter. In most cases, only partial CSI is available at the transmitter because of the limitations of the feedback channel. In a closed-loop MIMO system the input-output relationship with a closed-loop approach can be described as

 

where   is the   vector of transmitted symbols,   are the   vectors of received symbols and noise respectively,   is the   matrix of channel coefficients and   is the   linear precoding matrix.

A precoding matrix   is used to precode the symbols in the vector to enhance the performance. The column dimension   of   can be selected smaller than   which is useful if the system requires   streams because of several reasons. Examples of the reasons are as follows: either the rank of the MIMO channel or the number of receiver antennas is smaller than the number of transmit antennas.

See also

edit

References

edit
  1. ^ Awad, Ehab (September 2015). "Multicore optical fiber Y-Splitter". Optics Express. 23 (20): 25661–25674. Bibcode:2015OExpr..2325661A. doi:10.1364/OE.23.025661. PMID 26480082.
  2. ^ Awad, Ehab (January 2018). "Confined optical beam-bending for direct connection among cores of different multi-core fibers". Optical and Quantum Electronics. 50 (2): 69. Bibcode:2018OptQE..50...69A. doi:10.1007/s11082-018-1344-0. S2CID 254897867.
  3. ^ Awad, Ehab (December 2015). "Data interchange across cores of multi-core optical fibers". Optical Fiber Technology. 26: 157. Bibcode:2015OptFT..26..157A. doi:10.1016/j.yofte.2015.10.003.
  4. ^ Ho, Keang-Po; Kahn, Joseph M. (2011). "Mode-dependent loss and gain: Statistics and effect on mode-division multiplexing". Optics Express. 19 (17): 16612–16635. arXiv:1105.3533. Bibcode:2011OExpr..1916612H. doi:10.1364/OE.19.016612. PMID 21935025.
  5. ^ Mello, Darli A. A.; Srinivas, Hrishikesh; Choutagunta, Karthik; Kahn, Joseph M. (2020-01-15). "Impact of Polarization- and Mode-Dependent Gain on the Capacity of Ultra-Long-Haul Systems". Journal of Lightwave Technology. 38 (2): 303–318. Bibcode:2020JLwT...38..303M. doi:10.1109/JLT.2019.2957110.
  6. ^ Antonelli, Cristian; Mecozzi, Antonio; Shtaif, Mark (2015). "The delay spread in fibers for SDM transmission: Dependence on fiber parameters and perturbations". Optics Express. 23 (3): 2196–2302. Bibcode:2015OExpr..23.2196A. doi:10.1364/OE.23.002196. PMID 25836090.