Parallel manipulator

(Redirected from Parallel robots)

A parallel manipulator is a mechanical system that uses several computer-controlled serial chains to support a single platform, or end-effector. Perhaps, the best known parallel manipulator is formed from six linear actuators that support a movable base for devices such as flight simulators. This device is called a Stewart platform or the Gough-Stewart platform in recognition of the engineers who first designed and used them.[1]

Abstract render of a Hexapod platform (Stewart Platform)
Over-actuated planar parallel ma­ni­pulator simulated with MeKin2D.

Also known as parallel robots, or generalized Stewart platforms (in the Stewart platform, the actuators are paired together on both the basis and the platform), these systems are articulated robots that use similar mechanisms for the movement of either the robot on its base, or one or more manipulator arms. Their 'parallel' distinction, as opposed to a serial manipulator, is that the end effector (or 'hand') of this linkage (or 'arm') is directly connected to its base by a number of (usually three or six) separate and independent linkages working simultaneously. No geometrical parallelism is implied.

Design features

edit

A parallel manipulator is designed so that each chain is usually short, simple and can thus be rigid against unwanted movement, compared to a serial manipulator. Errors in one chain's positioning are averaged in conjunction with the others, rather than being cumulative. Each actuator must still move within its own degree of freedom, as for a serial robot; however in the parallel robot the off-axis flexibility of a joint is also constrained by the effect of the other chains. It is this closed-loop stiffness that makes the overall parallel manipulator stiff relative to its components, unlike the serial chain that becomes progressively less rigid with more components.

This mutual stiffening also permits simple construction: Stewart platform hexapods chains use prismatic joint linear actuators between any-axis universal ball joints. The ball joints are passive: simply free to move, without actuators or brakes; their position is constrained solely by the other chains. Delta robots have base-mounted rotary actuators that move a light, stiff, parallelogram arm. The effector is mounted between the tips of three of these arms and again, it may be mounted with simple ball-joints. Static representation of a parallel robot is often akin to that of a pin-jointed truss: the links and their actuators feel only tension or compression, without any bending or torque, which again reduces the effects of any flexibility to off-axis forces.

A further advantage of the parallel manipulator is that the heavy actuators may often be centrally mounted on a single base platform, the movement of the arm taking place through struts and joints alone. This reduction in mass along the arm permits a lighter arm construction, thus lighter actuators and faster movements. This centralisation of mass also reduces the robot's overall moment of inertia, which may be an advantage for a mobile or walking robot.

All these features result in manipulators with a wide range of motion capability. As their speed of action is often constrained by their rigidity rather than sheer power, they can be fast-acting, in comparison to serial manipulators.

Lower mobility

edit

A manipulator can move an object with up to 6 degrees of freedom (DoF), determined by 3 translation 3T and 3 rotation 3R coordinates for full 3T3R mobility. However, when a manipulation task requires less than 6 DoF, the use of lower mobility manipulators, with fewer than 6 DoF, may bring advantages in terms of simpler architecture, easier control, faster motion and lower cost.[2]  For example, the 3 DoF Delta [3][4] robot has lower 3T mobility and has proven to be very successful for rapid pick-and-place translational positioning applications. The workspace of lower mobility manipulators may be decomposed into `motion’ and `constraint’ subspaces. For example, 3 position coordinates constitute the motion subspace of the 3 DoF Delta robot and the 3 orientation coordinates are in the constraint subspace.  The motion subspace of lower mobility manipulators may be further decomposed into independent (desired) and dependent subspaces: consisting of `concomitant’ or `parasitic’ motion which is undesired motion of the manipulator.[5][6][7]  The debilitating effects of parasitic motion should be mitigated or eliminated in the successful design of lower mobility manipulators.  For example, the Delta robot does not have parasitic motion since its end effector does not rotate.

Comparison to serial manipulators

edit
 
Hexapod positioning systems, also known as Stewart Platforms.

Most robot applications require rigidity. Serial robots may achieve this by using high-quality rotary joints that permit movement in one axis but are rigid against movement outside this. Any joint permitting movement must also have this movement under deliberate control by an actuator. A movement requiring several axes thus requires a number of such joints. Unwanted flexibility or sloppiness in one joint causes a similar sloppiness in the arm, which may be amplified by the distance between the joint and the end-effectuor: there is no opportunity to brace one joint's movement against another. Their inevitable hysteresis and off-axis flexibility accumulates along the arm's kinematic chain; a precision serial manipulator is a compromise between precision, complexity, mass (of the manipulator and of the manipulated objects) and cost. On the other hand, with parallel manipulators, a high rigidity may be obtained with a small mass of the manipulator (relatively to the charge being manipulated). This allows high precision and high speed of movements, and motivates the use of parallel manipulators in flight simulators (high speed with rather large masses) and electrostatic or magnetic lenses in particle accelerators (very high precision in positioning large masses).

 
A five-bar parallel robot[8]
 
Sketchy, a portrait-drawing delta robot[9]

A drawback of parallel manipulators, in comparison to serial manipulators, is their limited workspace. As for serial manipulators, the workspace is limited by the geometrical and mechanical limits of the design (collisions between legs maximal and minimal lengths of the legs). The workspace is also limited by the existence of singularities, which are positions where, for some trajectories of the movement, the variation of the lengths of the legs is infinitely smaller than the variation of the position. Conversely, at a singular position, a force (like gravity) applied on the end-effector induce infinitely large constraints on the legs, which may result in a kind of "explosion" of the manipulator. The determination of the singular positions is difficult (for a general parallel manipulator, this is an open problem). This implies that the workspaces of the parallel manipulators are, usually, artificially limited to a small region where one knows that there is no singularity.

Another drawback of parallel manipulators is their nonlinear behavior: the command which is needed for getting a linear or a circular movement of the end-effector depends dramatically on the location in the workspace and does not vary linearly during the movement.

Applications

edit

Major industrial applications of these devices are:

They have also become more popular:

  • in high speed, high-accuracy positioning with limited workspace, such as in assembly of PCBs
  • as micro manipulators mounted on the end effector of larger but slower serial manipulators
  • as high speed/high-precision milling machines

Parallel robots are usually more limited in the workspace; for instance, they generally cannot reach around obstacles. The calculations involved in performing a desired manipulation (forward kinematics) are also usually more difficult and can lead to multiple solutions.

 
Prototype of "PAR4", a 4-degree-of-freedom, high-speed, parallel robot.

Two examples of popular parallel robots are the Stewart platform and the Delta robot.

See also

edit

References

edit
  1. ^ Merlet, J.P. (2008). Parallel Robots, 2nd Edition. Springer. ISBN 978-1-4020-4132-7.
  2. ^ Di, Raffaele (2006-12-01), Cubero, Sam (ed.), "Parallel Manipulators with Lower Mobility", Industrial Robotics: Theory, Modelling and Control, Pro Literatur Verlag, Germany / ARS, Austria, doi:10.5772/5030, ISBN 978-3-86611-285-8, retrieved 2020-12-03
  3. ^ Device for the movement and positioning of an element in space, R. Clavel - US Patent 4,976,582, 1990
  4. ^ R. Clavel, Delta: a fast robot with parallel geometry, Proc 18th Int Symp Ind Robots; Sydney, Australia (1988), pp. 91-100
  5. ^ Nigatu, Hassen; Yihun, Yimesker (2020), Larochelle, Pierre; McCarthy, J. Michael (eds.), "Algebraic Insight on the Concomitant Motion of 3RPS and 3PRS PKMS", Proceedings of the 2020 USCToMM Symposium on Mechanical Systems and Robotics, Mechanisms and Machine Science, vol. 83, Cham: Springer International Publishing, pp. 242–252, doi:10.1007/978-3-030-43929-3_22, ISBN 978-3-030-43928-6, S2CID 218789290, retrieved 2020-12-13
  6. ^ Nigatu, Hassen; Choi, Yun Ho; Kim, Doik (2021-10-01). "Analysis of parasitic motion with the constraint embedded Jacobian for a 3-PRS parallel manipulator". Mechanism and Machine Theory. 164: 104409. doi:10.1016/j.mechmachtheory.2021.104409. ISSN 0094-114X.
  7. ^ Nigatu, Hassen; Kim, Doik (2021-01-01). "Optimization of 3-DoF Manipulators' Parasitic Motion with the Instantaneous Restriction Space-Based Analytic Coupling Relation". Applied Sciences. 11 (10): 4690. doi:10.3390/app11104690.
  8. ^ "DexTAR - an educational parallel robot". Archived from the original on 2014-05-29.
  9. ^ "Sketchy, a home-constructed drawing robot". Jarkman.
  10. ^ "Active and Passive Fiber Alignment". Archived from the original on 2006-12-11. Retrieved 2007-03-29.

Further reading

edit
  •  
    [1][2] Parallel manipulator with parasitic motion.
    Gogu, Grigore (2008). Structural Synthesis of Parallel Robots, Part 1: Methodology. Springer. ISBN 978-1-4020-5102-9.
  • Gogu, Grigore (2009). Structural Synthesis of Parallel Robots, Part 2: Translational topologies with Two and Three Degrees of Freedom. Springer. ISBN 978-1-4020-9793-5.
  • Merlet, J.P. (2008). Parallel Robots, 2nd Edition. Springer. ISBN 978-1-4020-4132-7.
  • Kong, X.; Gosselin, C. (2007). Type Synthesis of Parallel Mechanisms. Springer. ISBN 978-3-540-71989-2.
  • Gallardo-Alvarado, J. (2016). Kinematic Analysis of Parallel Manipulators by Algebraic Screw Theory. Springer. ISBN 978-3-319-31124-1.
edit