Reefing reduces the area of a sail, usually by folding or rolling one edge of the canvas in on itself and attaching the unused portion to a spar or a stay, as the primary measure to preserve a sailing vessel's stability in strong winds. Restoring full sail area is termed shaking out a reef.[1]

Reefed Sail
Gaff sail, showing reefing cringles (13), reefing points (20) and reefing lines (21)

Whereas fore-and-aft rigged vessels store the unused portion of the sail on a boom (below the sail), square-rigged vessels stow the unused portion on a spar above the sail. Reefing may occur by rolling the sail around its luff or foot, either on a rotating stay or within a spar.

Fore-and-aft rigs

edit
 
A genoa jib completely furled around the forestay, and mainsail partially furled within the mast (forming a reef) on a Bavaria 36 sloop

Sails may have built-in alternative attachment points that allow their area to be reduced. In a mainsail, pairs of grommets, called reefing tacks, reefing clews, or reefing cringles may be installed in the sail; a cruising boat will typically have two to three pairs. Pulling these points down to the boom forms a new tack and clew, reducing the sail's area. Using the pair of grommets closest to the boom is called a single reef, using the next pair is called a double reef, and so on. A sail may have reef points, grommeted holes in the sail between the reefing tacks. These are used with reefing lines or buntlines to secure the excess fabric of the sail after reefing to minimize flogging and improve visibility from the cockpit.[2][1]

Slab

edit

Slab or jiffy reefing allows for the quick establishment of a new tack and clew, while the halyard is partially lowered and then raised. One or two reefing lines passing through the sail's luff and leach reef cringles create a new tack and clew for the sail by pulling those points tight to the boom. These can be led back to the cockpit to allow crew members to reef without going on deck in heavy weather. Intermediate reef cringles need not be used.[3][4]

Roller

edit

Roller reefing rolls or wraps the sail around a wire, foil, or spar to reduce its exposure to the wind. In mainsail furling systems the sail is either wrapped around the boom by a mechanism in the gooseneck or hardware inside the boom winds it around a rotating foil. Furling systems controlled with lines led to the cockpit allow reefing without crew having to go on deck in heavy weather. Roller reefing also allows more variable sail area than conventional or jiffy reefing. Countering these advantages are the furled sail possibly not having an optimal shape and sail repair or replacement being more difficult. In-mast roller-furling mainsails are not conducive to good sail shape.[3]

Square rigs

edit
 
Square-rigged, 18th-century frigate, showing reef bands across the sails.

Square-rigged sails hang from a spar, called a yard. When reefed, the sail is pulled upwards and affixed to the yard at one of the reef bands that runs horizontally across the sail. Each reef band is a canvas-reinforced strip, which contains cringles—eyes through which the reef lines pass that attach the sail to the yard. A sail may have several reef bands to shorten sail to different degrees.[5]

See also

edit

References

edit
  1. ^ a b Bingham, Bruce (20 May 2015). "How to Reef the Main". Cruising World. Retrieved 3 April 2016.
  2. ^ Jobson, Gary (1998). Sailing Fundamentals. Simon & Schuster. ISBN 0684849941.
  3. ^ a b Howard, James D.; Howard, Jim; Doane, Charles J. (2000). Handbook of Offshore Cruising: The Dream and Reality of Modern Ocean Cruising. Sheridan House, Inc. p. 170. ISBN 978-1-57409-093-2.
  4. ^ Caswell, Chris (2001). Chartering a Boat: Sail and Power. Sheridan House, Inc. p. 90. ISBN 978-1-57409-111-3.
  5. ^ Mayne, Richard (2018-10-24). The Language of Sailing. Routledge. p. 233. ISBN 978-1-135-96558-7.

Rousemaniere, John (7 January 2014). The Annapolis Book of Seamanship. ISBN 978-1451650198.