Pennsylvania Turnpike

This article is about the Pennsylvania Turnpike mainline running from Ohio to New Jersey. For other uses, see Pennsylvania Turnpike (disambiguation).

The Pennsylvania Turnpike, sometimes shortened to Penna Turnpike or PA Turnpike, is a controlled-access toll road that is operated by the Pennsylvania Turnpike Commission (PTC) in the Commonwealth of Pennsylvania in the United States. It runs for 360 miles (580 km) across the state, connecting Pittsburgh in Western Pennsylvania with Philadelphia in eastern Pennsylvania, and passes through four tunnels as it crosses the Appalachian Mountains in central Pennsylvania.

Pennsylvania Turnpike
Pennsylvania Turnpike mainline highlighted in green
Route information
Maintained by PTC
Length	360.09 mi (579.51 km)
Existed	October 1, 1940–present
History	Section to Upper Merion Township completed on November 20, 1950, section to the Ohio State line completed December 1, 1954, section to the New Jersey state line completed on May 23, 1956; Current road at Laurel Hill opened on October 30, 1964; current road at the Sideling Hill and Rays Hill opened November 26, 1968
Component highways	I-76 from the Ohio state line to Valley Forge I-70 from New Stanton to Breezewood I-276 from Valley Forge to Bristol Township I-95 from Bristol Township to the New Jersey state line
Restrictions	No hazardous goods allowed in tunnels
Major junctions
West end	I-76 / Ohio Turnpike at the Ohio state line
Major intersections	I-79 / US 19 in Cranberry Township I-376 / US 22 / US 22 Bus. in Monroeville I-70 / US 119 / PA Turnpike 66 in New Stanton US 220 / US 220 Bus. in Bedford I-70 / US 30 in Breezewood I-83 in New Cumberland US 11 in Carlisle I-76 near Valley Forge I-476 / Penna Turnpike NE Extension in Plymouth Meeting I-95 in Bristol Township
East end	I-95 / Pearl Harbor Extension at the New Jersey state line
Location
Country	United States
State	Pennsylvania
Counties	Lawrence, Beaver, Butler, Allegheny, Westmoreland, Somerset, Bedford, Fulton, Huntingdon, Franklin, Cumberland, York, Dauphin, Lebanon, Lancaster, Berks, Chester, Montgomery, Bucks
Highway system
Pennsylvania State Route System Interstate US State Scenic Legislative
← PA 75 I-76 → PA 76 ← PA 274 I-276 → PA 276 ← I-279 I-280 → PA 280
Pennsylvania Historical Marker
Designated	1990

Part of the Interstate Highway System, it is designated as part of Interstate 76 (I-76) between the Ohio state line and Valley Forge, I-70 runs concurrent with I-76 between New Stanton and Breezewood, Interstate 276 (I-276) between Valley Forge and Bristol Township, and I-95 from Bristol Township to the New Jersey state line.

The turnpike's western terminus is located at the Ohio state line in Lawrence County, where the road continues west as the Ohio Turnpike. The eastern terminus is situated at the New Jersey state line at the Delaware River–Turnpike Toll Bridge, which crosses the Delaware River in Bucks County. The road then continues east as the Pearl Harbor Memorial Extension of the New Jersey Turnpike.

The road uses an all-electronic tolling system; tolls may be paid using E-ZPass or toll by plate, which uses automatic license plate recognition. Historically, cash tolls were collected using a combination of the ticket system and a barrier toll system, but cash tolls were phased out between 2016 and 2020. The turnpike also offers 15 service plazas, providing food and fuel to travelers.

During the 1930s, the Pennsylvania Turnpike was designed to improve automobile transportation across the mountains of Pennsylvania, using seven tunnels built for the abandoned South Pennsylvania Railroad in the 1880s.

The road opened in 1940 between Irwin and Carlisle. It was one of the earlier long-distance limited-access highways in the United States and served as a precedent for additional limited-access toll roads and the Interstate Highway System. The Pennsylvania Turnpike was extended east to Valley Forge in 1950 and west to the Ohio state line in 1951. In 1954, the road was extended further east to the Delaware River, and construction began on the Northeast Extension of the turnpike. The mainline turnpike was finished in 1956 with the completion of the Delaware River Bridge.

During the 1960s, an additional tube was bored at four of the two-lane tunnels, while the other three tunnels were bypassed; these improvements made the entire length of the mainline turnpike four lanes wide. Improvements continue to be made to the road: rebuilding the roadway to modern standards, widening portions of the turnpike to six lanes, and adding interchanges. In 2018, an ongoing interchange project saw the redesignation of the easternmost three miles (4.8 km) of the road from I-276 to I-95. Though still considered part of the turnpike mainline, it is no longer signed with turnpike markers and uses I-95's mileposts and exit numbers.

Route description

The turnpike runs east to west across Pennsylvania, from the Ohio state line in Lawrence County east to the New Jersey state line in Bucks County. It passes through the Pittsburgh, Harrisburg, and Philadelphia areas, along with farmland and woodland. The highway crosses the Appalachian Mountains in the central part of the state, passing through four tunnels. The PTC, created in 1937 to construct, finance, operate, and maintain the road, controls the highway. In 2015, the roadway had an annual average daily traffic count ranging from a high of 120,000 vehicles between the Norristown interchange and I-476 to a low of 12,000 vehicles between the Ohio state line and the interchange with I-79 and U.S. Route 19 (US 19).

As part of the Interstate Highway System, the turnpike is part of the National Highway System, a network of roads important to the country's economy, defense, and mobility.

The Pennsylvania Turnpike is designated as a Blue Star Memorial Highway honoring those who have served in the United States Armed Forces; the Garden Club Federation of Pennsylvania has placed Blue Star Memorial Highway markers at service plazas along the turnpike.

In addition to the east–west mainline, the PTC also operates the Northeast Extension of the Pennsylvania Turnpike (I-476), the Beaver Valley Expressway (I-376), the Mon–Fayette Expressway (Pennsylvania Route 43 or PA 43), the Amos K. Hutchinson Bypass (PA 66), and the Southern Beltway (PA 576).

Western Extension

Westbound approaching the Pittsburgh interchange with I-376/US 22 in Monroeville

The Pennsylvania Turnpike begins at the Ohio state line in Lawrence County, beyond which the highway continues west as the Ohio Turnpike. From the state line, the turnpike heads southeast as a four-lane freeway designated as I-76 through rural areas south of New Castle. A short distance from the Ohio state line, the eastbound lanes come to the all-electronic Gateway toll gantry. The highway then crosses into Beaver County, where it reaches its first interchange with I-376 (here, the part called Beaver Valley Expressway) in Big Beaver.

After this interchange, the turnpike passes under Norfolk Southern's Koppel Secondary rail line before it reaches the exit for PA 18 near Homewood. Past PA 18, the highway crosses CSX's Pittsburgh Subdivision rail line, the Beaver River, and Norfolk Southern's Youngstown Line on the Beaver River Bridge. The road then enters Butler County, where it comes to Cranberry Township. Here, an interchange serves I-79 and US 19. The turnpike continues through a mix of rural land and suburban residential development north of Pittsburgh into Allegheny County.

The road then approaches the Warrendale toll gantry, where the closed toll system begins, and continues southeast, passing over the P&W Subdivision rail line, which is owned by CSX and operated by the Buffalo and Pittsburgh Railroad. East of this point, the turnpike has an interchange with PA 8 in Hampton Township. The turnpike then comes to the Allegheny Valley exit in Harmar Township, which provides access to PA 28 via Freeport Road. East of this interchange, the road heads south, with Canadian National's Bessemer Subdivision rail line parallel to the east of the road. The highway crosses Norfolk Southern's Conemaugh Line, the Allegheny River, and the Allegheny Valley Railroad's Allegheny Subdivision line on the six-lane Allegheny River Turnpike Bridge.

After crossing the Allegheny River, the turnpike returns to four lanes, passing through the Oakmont Country Club before coming to a bridge over Canadian National's Bessemer Subdivision. From here, the railroad tracks run along the west side of the road before splitting further to the west. The highway heads southeast to Monroeville, an eastern suburb of Pittsburgh; an interchange with the eastern terminus of I-376 and US 22 (Penn–Lincoln Parkway) provides access to Pittsburgh. East of Monroeville, the turnpike continues through eastern Allegheny County before crossing into Westmoreland County. Here, it heads south and passes over Norfolk Southern's Pittsburgh Line before it comes to the exit for US 30 near Irwin.

Original mainline

After the Irwin interchange, the Pennsylvania Turnpike widens to six lanes and heads into rural areas west of Greensburg. Curving southeast, it reaches New Stanton, where an interchange provides access to I-70, US 119, and the southern terminus of PA 66 (Amos K. Hutchinson Bypass). The road narrows back to four lanes at this interchange, and I-70 forms a concurrency with I-76 on the turnpike. After New Stanton, the road passes over the Southwest Pennsylvania Railroad's Radebaugh Subdivision line and winds southeast to the exit for PA 31 in Donegal, which also provides access to PA 711. Continuing east past Donegal, the turnpike crosses Laurel Hill into Somerset County.

In this county, the road continues southeast to Somerset and an interchange with PA 601 accessing US 219 and Johnstown before it crosses over CSX's S&C Subdivision rail line. East of Somerset, the highway passes north of the Somerset Wind Farm before it reaches Allegheny Mountain, going under the mountain in the Allegheny Mountain Tunnel. Exiting the tunnel, the turnpike winds down the mountain at a three-percent grade, which is the steepest grade on the turnpike, and heads into Bedford County, passing through a valley. At Bedford, an exit for US 220 Business (US 220 Bus.) provides access to US 220 and the southern terminus of I-99; this exit also serves Altoona to the north.

Eastbound at the Breezewood interchange, where I-70 splits from I-76

East of Bedford the turnpike passes through The Narrows, a gap in Evitts Mountain. The turnpike, US 30, and the Raystown Branch Juniata River all pass through the 650-foot-wide (200 m) narrows. The road winds through a valley south of the river, before traversing Clear Ridge Cut near Everett. Further east, at Breezewood, I-70 leaves the turnpike at an interchange with US 30; this interchange is notably home to some of the only traffic lights on an Interstate Highway.

After Breezewood, I-76 continues along the turnpike, heading northeast across Rays Hill into Fulton County. The turnpike continues east across Sideling Hill, before reaching an interchange with US 522 in Fort Littleton. After this interchange, the highway parallels US 522 before curving east into Huntingdon County. The turnpike goes under Tuscarora Mountain through the Tuscarora Mountain Tunnel, entering Franklin County. It then curves northeast into a valley to the exit for PA 75 in Willow Hill.

Again heading east, the road passes under Kittatinny Mountain through the Kittatinny Mountain Tunnel. Shortly after exiting the tunnel, the highway enters the Blue Mountain Tunnel under Blue Mountain. Leaving that tunnel, the turnpike heads northeast along the base of Blue Mountain to an exit for PA 997. East of this interchange, the road enters Cumberland County, heading east through the Cumberland Valley on a stretch known as "the straightaway". Further east, the turnpike reaches Carlisle and an interchange with US 11 providing access to I-81.

Philadelphia Extension

Westbound past the PA 29 interchange in Charlestown Township

Approaching Harrisburg, the Pennsylvania Turnpike heads east through a mixture of rural land and suburban development, passing over Norfolk Southern's Shippensburg Secondary rail line. In Upper Allen Township, the highway comes to the US 15 interchange accessing Gettysburg to the south and Harrisburg to the north. The road continues east and passes over Norfolk Southern's Lurgan Branch rail line before it heads into York County, where it reaches the interchange with I-83 serving Harrisburg, its western suburbs, and York to the south.

East of I-83, the turnpike widens to six lanes and crosses over Norfolk Southern's Port Road Branch rail line, the Susquehanna River, Amtrak's Keystone Corridor rail line, and Norfolk Southern's Royalton Branch rail line on the Susquehanna River Bridge. Now in Dauphin County, the road heads south of Harrisburg as a bypass.

In Lower Swatara Township the turnpike reaches an interchange with the southern end of I-283, serving Harrisburg and its eastern suburbs and providing access to PA 283; the PTC headquarters are located adjacent to this interchange. Here, the road narrows back to four lanes and runs through suburban development north of Middletown. The roadway passes over the Middletown and Hummelstown Railroad and the Swatara Creek before it continues into rural areas. The turnpike crosses a corner of Lebanon County before entering Lancaster County.

In Lancaster County, the highway passes through Pennsylvania Dutch Country and comes to an interchange with PA 72 accessing Lebanon to the north and Lancaster to the south. Further east, the turnpike passes over an East Penn Railroad line in Denver before it reaches an interchange with US 222 and PA 272 which serves the cities of Reading and Lancaster. The route continues into Berks County and comes to an interchange with the southern terminus of I-176 (a freeway to Reading) and PA 10 in Morgantown that also provides access to PA 23.

The turnpike then enters Chester County, running southeast to an exit for PA 100 north of Downingtown, where it heads into the western suburbs of Philadelphia. Continuing east, it reaches an interchange with PA 29 near Malvern. The highway crosses into Montgomery County and comes to the Valley Forge interchange in King of Prussia, where I-76 splits from the turnpike and heads southeast as the Schuylkill Expressway toward Philadelphia; this interchange also provides access to US 202 and US 422.

Delaware River Extension

Interstate 276
Location	Upper Merion Township–Bristol Township
Length	29.78 mi (47.93 km)
Existed	1964–present

Eastbound past the Mid-County interchange with I-476 in Plymouth Meeting

Starting at the Valley Forge interchange, the turnpike is designated as I-276 and becomes a six-lane road serving as a suburban commuter highway. The road comes to a bridge over SEPTA's Norristown High Speed Line and runs parallel to Norfolk Southern's Dale Secondary rail line, which is located south of the road. The turnpike crosses Norfolk Southern's Harrisburg Line, the Schuylkill River, and SEPTA's Manayunk/Norristown Line on the Schuylkill River Bridge near Norristown. A short distance later, the road passes over the Schuylkill River Trail and Norfolk Southern's Morrisville Connecting Track on the Schuylkill River Bridge before the parallel Dale Secondary rail line heads further south from the road.

In Plymouth Meeting, an interchange with Germantown Pike provides access to Norristown before the roadway reaches the Mid-County Interchange. This interchange connects to I-476, which heads south as the Mid-County Expressway, locally known as the "Blue Route", and north as the Northeast Extension of the turnpike, connecting the mainline turnpike to the Lehigh Valley and the Pocono Mountains regions of Pennsylvania.

After the Mid-County Interchange, the mainline turnpike heads east through the northern suburbs of Philadelphia. In Fort Washington, the highway passes over SEPTA's Lansdale/Doylestown Line before it has an interchange with PA 309. At this point, the road becomes parallel to Norfolk Southern's Morrisville Line, which is located a short distance to the south of the road. One mile (1.6 km) later, the turnpike has a westbound exit and entrance for Virginia Drive. In Willow Grove, the highway reaches the PA 611 exit before passing over SEPTA's Warminster Line. The turnpike continues through more suburban areas, crossing into Bucks County and coming to a bridge over Norfolk Southern's Morrisville Line. Farther east, the roadway passes over SEPTA's West Trenton Line. In Bensalem Township, the highway comes to a bridge over CSX's Trenton Subdivision rail line before reaching an interchange with US 1, which provides access to Philadelphia.

Westbound in Upper Southampton Township

The highway narrows back to four lanes before an eastbound exit and entrance with PA 132. A short distance later, the turnpike arrives at the eastern end of the closed toll system at the Neshaminy Falls toll gantry. After passing through more suburbs, the road reaches a partial interchange with I-95, where it crosses under I-295 with no access; this interchange has access from the westbound turnpike to southbound I-95 and from northbound I-95 to the eastbound turnpike. At this point, I-276 ends and the Pennsylvania Turnpike becomes part of I-95. Here, signage indicates the westbound turnpike as a left exit from southbound I-95, using I-95 milepost exit number 40. This is the only place where continuing on the mainline turnpike is signed as an exit.

After joining I-95, the remaining three miles (4.8 km) of road uses I-95's mileposts and exit numbers and is not directly signed as the Pennsylvania Turnpike, though it is still considered part of the mainline turnpike. Continuing east, the turnpike reaches its final interchange, providing access to US 13 near Bristol. Following this, the road passes over an East Penn Railroad line before it comes to the westbound all-electronic Delaware River Bridge toll gantry. After this, the highway crosses the Delaware Canal and Amtrak's Northeast Corridor rail line before heading across the Delaware River into New Jersey on the Delaware River–Turnpike Toll Bridge. At this point, the Pennsylvania Turnpike ends, and I-95 continues east (north) as the Pearl Harbor Memorial Extension of the New Jersey Turnpike, which connects to the mainline of the New Jersey Turnpike.

Major bridges and tunnels

Aerial view of Blue Mountain and Kittatinny Mountain tunnels, also seen in this photo is the six degree curve near the Blue Mountain Tunnels eastern portal, which was replaced by current alignment in the early 2010s

West portal of the Allegheny Mountain Tunnel

The Pennsylvania Turnpike incorporates several major bridges and tunnels along its route. Four tunnels cross central Pennsylvania's Appalachian Mountains. The 6,070-foot (1,850 m) Allegheny Mountain Tunnel passes under Allegheny Mountain in Somerset County. The Tuscarora Mountain Tunnel runs beneath Tuscarora Mountain at the border of Huntingdon and Franklin counties, and is 5,236 feet (1,596 m) long. The Kittatinny Mountain and Blue Mountain tunnels are adjacent to each other in Franklin County and are 4,727 feet (1,441 m) and 4,339 feet (1,323 m) long, respectively. Formerly, the turnpike also traveled through the Laurel Hill Tunnel, Sideling Hill Tunnel, and Rays Hill Tunnel, though these were replaced in the 1960s after traffic levels rendered their nonstandard design obsolete.

Five bridges carry the turnpike over major rivers in the state. The 1,545-foot-long (471 m) Beaver River Bridge crosses the Beaver River in Beaver County, which is in the process of being replaced. The highway crosses the Allegheny River in Allegheny County on the 2,350-foot-long (720 m) Allegheny River Turnpike Bridge, which replaced a deck truss bridge of the same name from 1951. The toll road crosses the Susquehanna River between York and Dauphin counties on the 5,910-foot-long (1,800 m) Susquehanna River Bridge, which also replaced a deck truss bridge from the early 1950s. In Montgomery County, the turnpike crosses the Schuylkill River on the 1,224-foot-long (373 m) Schuylkill River Bridge, which was twinned in the 2000s. At the New Jersey state line in Bucks County, the highway is connected to the Pearl Harbor Memorial Extension of the New Jersey Turnpike by the 6,571-foot-long (2,003 m) Delaware River–Turnpike Toll Bridge over the Delaware River.

Tolls

Toll plaza at Somerset interchange before conversion to all-electronic tolling

The Pennsylvania Turnpike uses all-electronic tolling, with tolls payable by toll by plate (which uses automatic license plate recognition to take a photo of the vehicle's license plate and mail a bill to the vehicle owner) or E-ZPass. Between the Warrendale and Neshaminy Falls toll plazas on the mainline, as well as on the Northeast Extension from Mid-County to Wyoming Valley, tolls are based on distance traveled. An eastbound mainline toll gantry is located at Gateway near the Ohio state line and a westbound mainline toll gantry is located at the Delaware River Bridge near the New Jersey state line, both charging a flat toll. There is no toll between Gateway and Warrendale and between Neshaminy Falls and the Delaware River Bridge.

As of 2024, it costs a passenger vehicle $95.50 to travel the length of the mainline turnpike between Warrendale and Neshaminy Falls using toll by plate, and $47.30 using E-ZPass; the eastbound Gateway toll gantry costs $15.20 with toll by plate and $7.50 with E-ZPass for passenger vehicles while the westbound Delaware River Bridge toll gantry costs $9.70 using toll by plate and $7.30 using E-ZPass. Since 2009, the turnpike has raised tolls once a year, starting on January 1, to provide funding for increasing annual payments to the Pennsylvania Department of Transportation (PennDOT), as mandated by Act 44.

The turnpike commission paid PennDOT $450 million annually, of which $200 million went to non-turnpike highway projects across the state and $250 million went to funding mass transit. As part of Act 89 signed in 2013, the annual payments to PennDOT will end after 2022, 35 years earlier than the original proposal under Act 44. But it is not known if the annual toll increases will continue after 2022. Act 89 has also redirected the entire $450 million annual payments to PennDOT toward funding mass transit. With the annual rise in tolls, traffic has been shifting from the turnpike to local roads.

Until March 2020, the Pennsylvania Turnpike used the ticket system of tolling between the Warrendale and Neshaminy Falls toll plazas, as well as on the Northeast Extension from Mid-County to Wyoming Valley. When entering the turnpike, motorists received a ticket listing the toll for each exit; the ticket was surrendered when exiting, and the applicable toll was paid. If the ticket was lost, motorists were charged the maximum toll for that exit. Cash, credit cards, and E-ZPass were accepted at traditional toll plazas.

In 2010, McCormick Taylor and Wilbur Smith Associates were hired to conduct a feasibility study on converting the road to all-electronic tolls. On March 6, 2012, the turnpike commission announced that it was implementing this plan. The turnpike commission projected that it would save $65 million annually on labor costs by eliminating toll collectors. On January 3, 2016, all-electronic tolling was introduced in the westbound direction at the Delaware River Bridge mainline toll plaza, while the eastern terminus of the ticket system was moved from the Delaware River Bridge to Neshaminy Falls. On October 27, 2019, all-electronic tolling was implemented at the eastbound Gateway mainline toll plaza. All-electronic tolling was originally scheduled to be implemented on the entire length of the Pennsylvania Turnpike in the later part of 2021.

In March 2020, the turnpike made the switch early as a result of the COVID-19 pandemic. The all-electronic tolling system on the turnpike will initially use toll booths at exits until mainline toll gantries between interchanges are constructed.

Mainline toll gantries are planned to be in operation by 2025 east of the Reading interchange and by the later part of 2026 along the western portion of the turnpike.

As of 2020, about 86 percent of vehicles along the Pennsylvania Turnpike use E-ZPass for payment of tolls.

Act 44 toll increases

The turnpike commission raised tolls by 25 percent on January 4, 2009, to provide funds to PennDOT for road and mass-transit projects, as mandated by Act 44. This toll hike brought the rate to travel the turnpike to $0.074 per mile ($0.046/km) (equivalent to $0.1 per mile ($0.062/km) in 2023). At this point, an annual toll increase was planned.

A three-percent toll increase went into effect January 3, 2010, bringing the rate to $0.077 per mile ($0.048/km) (equivalent to $0.11/mi ($0.068/km) in 2023). The cash toll increased 10 percent on January 2, 2011, and E-ZPass tolls increased three percent. The new toll rate was $0.085 per mile ($0.053/km) (equivalent to $0.11/mi ($0.068/km) in 2023) using cash and $0.079 per mile ($0.049/km) (equivalent to $0.11/mi ($0.068/km) in 2023) using E-ZPass.

As part of this toll hike, the turnpike commission initially planned to omit the toll amount from new tickets, and Pennsylvania Auditor Jack Wagner wondered if the commission was trying to hide the increase. The commission later decided to include the tolls on new tickets.

Cash tolls increased 10 percent on January 1, 2012, while E-ZPass tolls were unchanged from the previous year. With this increase, the cash toll rate increased to $0.093 per mile ($0.058/km) (equivalent to $0.12/mi ($0.075/km) in 2023). Tolls for both cash and E-ZPass customers increased in January of each of the next eight years. In 2025, tolls will increase 5 percent, but tolls will change to be based on distance traveled as opposed to a flat rate. As a result, some drivers will see decreases in their tolls. Tolls are expected to increase annually until at least 2050.

An analysis by Australian insurance company Budget Direct found the Pennsylvania Turnpike to be the world's most expensive toll. Turnpike spokesman Carl DeFebo disputed Budget Direct's claim, saying that the analysis looked at all of the turnpike's toll roads together, noting "Nobody would ever go south towards Pittsburgh, east towards Philadelphia, then north towards Scranton. That's a 400-plus mile trip," and that Pennsylvania Turnpike tolls are comparable to other toll roads when examined on a per mile basis.

Services

Emergency assistance and information

Motorists needing assistance may dial *11 on mobile phones. First-responder service is available to all turnpike users via the GEICO Safety Patrol program. The free program checks for disabled motorists, debris, and accidents along the road and provides assistance 24 hours daily year-round. Each patrol vehicle covers a 20-to-25-mile (32 to 40 km) stretch of the turnpike. Towing service is available from authorized service stations near the highway, and Pennsylvania State Police Troop T patrols the turnpike. The troop's headquarters is in Highspire; its turnpike substations are grouped into two sections: the western section has substations in Gibsonia, New Stanton, Somerset, and Everett while the eastern section has substations in Newville, Bowmansville, and King of Prussia (the eastern section also has a substation at Pocono on the Northeast Extension). The PTC broadcasts road, traffic, and weather conditions over highway advisory radio transmitters at each exit on 1640 kHz AM, with a range of approximately two miles (3.2 km). The 511PA travel information service provides alerts, an interactive map, weather information, and traffic cameras to motorists. There are variable-message signs located along the roadway that provide information to motorists such as accidents, construction, weather, and traffic congestion.

Service plazas

Sideling Hill service plaza

The Pennsylvania Turnpike has 15 service plazas on the main highway throughout the state, as well as two on the Northeast Extension. Each plaza has multiple fast-food restaurants, a Sunoco gas station, and a 7-Eleven convenience store. Other amenities include ATMs, E-ZPass sales, free cellphone charging, Pennsylvania Lottery sales, picnic areas, restrooms, tourist information, Travel Board information centers, and Wi-Fi. The King of Prussia plaza has a welcome center, and the New Stanton and Sideling Hill plazas feature seasonal farmers' markets. A few plazas offer E85 while New Stanton offers compressed natural gas; all of them offer conventional gasoline and diesel fuel. Select service plazas have electric vehicle charging stations. The Sunoco and 7-Eleven locations as well as the Subway at North Midway are operated by 7-Eleven itself while the remaining restaurants and general upkeep of the service plazas are operated by Applegreen.

As early as 1946, many of the service plazas were expanded in order to accommodate booming popularity.

With the opening of the extensions from 1950 to 1956, new service plazas were also constructed along them. In comparison to the original ones, they were larger, and were more spaced out than those on the original.

In 1957, the Laurel Hill and New Baltimore Plazas were closed. In their place, the Somerset Plaza was later completed.

In 1968, the Sideling Hill plaza, which serves both westbound and eastbound traffic, was opened, replacing the Cove Valley plaza, which served only westbound traffic and needed to demolished due to the bypassing of the Rays Hill and Sideling Hill tunnels.

In 1978, as the Howard Johnson's exclusive contract to provide food service was ending, the turnpike commission considered bids for competitors to provide food service. That year, Aramark was awarded a contract for food service at two plazas, ending the Howard Johnson's monopoly. The highway became the first toll road in the country to offer more than one fast-food chain at its service plazas. At this time, gas stations along the turnpike were operated by Gulf Oil, Exxon, and ARCO.

The Denver, Pleasant Valley, and Mechanicsburg plazas were closed in 1980. That same year, Hardee's opened restaurants at the service plazas to compete with Howard Johnson's. With this, the turnpike became the first road in the world to offer fast food at its service plazas.

The eastbound Path Valley plaza closed in 1983 due to a lack of business since it was located only 15 miles (24 km) east of the newer, more accessible Sideling Hill plaza. That same year, Burger King and McDonald's opened on the Pennsylvania Turnpike. This marked a transition from sit-down to fast-food dining on the turnpike by popular demand.

With Marriott Corporation purchasing the remaining Howard Johnson's restaurants in 1987, replacement came to the final of the Howard Johnsons with new restaurants such as Roy Rogers and Bob's Big Boy.

In 1990, the Brandywine (now Peter J. Camiel) plaza was reconstructed, the first such major project in the turnpike's history. That same year, Gulf Oil LP replaced the Exxon stations on the turnpike.

In 1993, Sunoco took over operation of the gas stations, outbidding Shell US. With this, various improvements were made, such as adding credit card-activated pumps, fax machines, ATMs, and informational lodging boards.

In 1995, a farmers market was introduced to the Sideling Hill service plaza.

In 2002, the Butler plaza was closed to make way for the Warrendale Toll Plaza.

In 2004, an expansion of the Somerset Service Plaza was completed, months ahead of schedule.

The eastbound only Hempfield and South Neshaminy plazas were closed in 2007 for a six lane widening and new slip ramp, respectively. The eastbound Zelienople plaza closed in 2008 due to a lack of business since it was located on the stretch of the turnpike from Ohio to Warrendale which had been toll free since 2003. The westbound North Neshaminy plaza shut down in 2010 to allow for a future reconstruction.

In 2013, free Wi-Fi was introduced at all of the service plazas.

In 2006, the PTC and HMSHost started a system-wide project in which all service plazas would be reconstructed or extensively renovated, starting with the Oakmont Plum plaza, which closed in 2006 and reopened in 2007. This was followed by the reconstruction of the North Somerset and Sideling Hill plazas (2007–2008); New Stanton (2008–2009); King of Prussia (2009–2010); Lawn and Bowmansville (2010–2011); South Somerset, Blue Mountain, and Cumberland Valley (2011–2012); South Midway and Highspire (2012–2013); Peter J. Camiel (2013–2014); and Valley Forge and North Midway (2014–2015).

The Art Sparks program was launched in 2017 as a partnership between the turnpike commission and the Pennsylvania Council on the Arts to install public art created by local students in the Arts in Education residency program in service plazas along the turnpike over the next five years. The public art consists of a mural reflecting the area where the service plaza is located. The first Art Sparks mural debuted at the Lawn service plaza in May 2017.

In April 2019, the Sunoco/A-Plus locations began to be converted to 7-Eleven locations, as part of a larger deal that saw 7-Eleven take over Sunoco's company-owned convenience stores along the East Coast and Texas; Sunoco continues to supply fuel to the locations.

History

Before the turnpike

Before the turnpike, there were other forms of transportation across the Appalachians. Native Americans traveled across the mountains along wilderness trails; later, European settlers followed wagon roads to cross the state. The Philadelphia and Lancaster Turnpike opened between Lancaster and Philadelphia in 1794, the first successful turnpike in the United States. The road was paved with logs, an improvement on the dirt Native American trails. In 1834, the Main Line of Public Works opened as a system of canals, railroads, and cable railways across Pennsylvania to compete with the Erie Canal in New York.

The Pennsylvania Railroad was completed between Pittsburgh and Philadelphia in 1854. During the 1880s, the South Pennsylvania Railroad was proposed to compete with the Pennsylvania. It received the backing of William Henry Vanderbilt, head of the New York Central Railroad (the Pennsylvania's chief rival). Andrew Carnegie also provided financial support, since he was unhappy with rates charged by the Pennsylvania Railroad. Construction began on the rival line in 1883 but stopped when the railroads reached an agreement in 1885. After construction halted, the only vestiges of the South Pennsylvania were nine tunnels, some roadbed, and piers for a bridge over the Susquehanna River in Harrisburg.

Winding section east of Fort Littleton in 1942

As a result of the challenge of crossing the Pennsylvania mountains by automobile, William Sutherland of the Pennsylvania Motor Truck Association and Victor Lecoq of the Pennsylvania State Planning Commission proposed a toll highway in 1934. This highway would be a four-lane limited-access road modeled after the German Autobahn routes and Connecticut's Merritt Parkway. The turnpike could also serve as a defense road, and construction costs could be reduced by using the abandoned tunnels of the South Pennsylvania Railroad project.

In 1935, Sutherland and Lecoq introduced their turnpike idea to state legislator Cliff Patterson, who proposed a feasibility study on April 23, 1935. The proposal passed, and the Works Progress Administration (WPA) explored the possibility of building the road. Its study estimated a cost of between $60 and $70 million (equivalent to between $1.05 billion and $1.22 billion in 2023) to build the turnpike. Patterson introduced Bill 211 to the legislature, calling for the establishment of the PTC. The bill was signed into law by Governor George Howard Earle III on May 21, 1937, and, on June 4, the first commissioners were appointed. The highway was planned to run from US 30 in Irwin (east of Pittsburgh) east to US 11 in Middlesex (west of Harrisburg), a length of about 162 miles (261 km). It would pass through nine tunnels along the way.

The road was planned to have four lanes, with a median and no grade steeper than three percent. Access to the highway would be controlled by entrance and exit ramps. There would be no at-grade intersections, driveways, traffic lights, crosswalks, or at-grade railroad crossings. Curves would be wide and road signage large. The right-of-way for the turnpike would be 200 feet (61 m); the road would be 24 feet (7.3 m) wide, with 10-foot (3.0 m) shoulders and a 10-foot (3.0 m) median. Through the tunnels, the road would have two lanes, a 14-foot (4.3 m) clearance, and a 23-foot-wide (7.0 m) roadway. The turnpike's design would be uniform for its entire length.

In February 1938, the commission began investigating proposals for $55 million in bonds to be issued for construction of the turnpike. A month later, Van Ingen and Company purchased $60 million (equivalent to $1.02 billion in 2023) in bonds that they would offer to the public. President Franklin D. Roosevelt approved a $24-million (equivalent to $408 million in 2023) grant from the WPA in April 1938 for construction of the road; the commonwealth also contributed $29 million (equivalent to $492 million in 2023) toward the project.

The WPA grant received final approval, but plans were still made to sell bonds; the first issue was planned for about $20 million (equivalent to $340 million in 2023). The reduced bond issue was due to the grant from the WPA.

In June, the Reconstruction Finance Corporation (RFC) announced they would lend the commission sufficient funds to build the road. The RFC loan totaled $32 million (equivalent to $543 million in 2023), with a $26 million (equivalent to $442 million in 2023) grant from the Public Works Administration (PWA), providing $58 million (equivalent to $985 million in 2023) for the turnpike's construction; highway tolls would repay the RFC.

In October 1938, the turnpike commission agreed with the RFC and PWA that the RFC would purchase $35 million (equivalent to $594 million in 2023) in bonds, in addition to the PWA grant. That month, a banking syndicate purchased the entire bond amount from the RFC. The previous month, a proposal was rejected that would have constructed a railroad from Pittsburgh to Harrisburg using the former South Pennsylvania Railroad right-of-way that had been designated for the turnpike.

The highway opened in 1940 between Irwin and Carlisle as the first long-distance controlled-access highway in the United States. Following its completion, other toll roads and the Interstate Highway System were built. The highway was extended east to Valley Forge in 1950 and west to the Ohio state line in 1951. It was routed east to the New Jersey state line (the Delaware River) in 1954; the Delaware River Bridge opened two years later, completing the turnpike.

Design

Laurel Hill Tunnel in 1942

To build the turnpike, boring of the former railroad tunnels had to be completed. Since the Allegheny Mountain Tunnel bore was in poor condition, a new bore was drilled 85 feet (26 m) to the south. The commission considered bypassing the Rays Hill and Sideling Hill tunnels, but the cost of a bypass was considered too high. Crews used steam shovels to widen the tunnels' portals, and temporary railroad tracks transported construction equipment in and out. Concrete was used in lining the tunnel portals. The tunnels included ventilation ducts, drainage structures, sidewalks, lighting, telephone, and signal systems. Lighting was installed along the roadway approaching the tunnel portals.

The tunnels bored through the seven mountains totaled 4.5 miles (7.2 km). The tunnels were Laurel Hill Tunnel, Allegheny Mountain Tunnel, Rays Hill Tunnel, Sideling Hill Tunnel, Tuscarora Mountain Tunnel, Kittatinny Mountain Tunnel, and Blue Mountain Tunnel, and the road became known as the "tunnel highway".

Many bridge designs were used for roads over the highway, including the concrete arch bridge, the through plate girder bridge, and the concrete T-beam bridge. Bridges used to carry the turnpike over other roads and streams included a concrete arch viaduct in New Stanton. At 600 feet (180 m), the New Stanton viaduct was the longest bridge along the original section of the turnpike. Other turnpike bridges included plate girder bridges such as the bridge over Dunnings Creek in the Bedford Narrows. Smaller concrete T-beam bridges were also built. A total of 307 bridges were constructed along the original section of the turnpike.

Eleven interchanges were built along the turnpike, most of which were trumpet interchanges in which all ramps merge at the toll booths. Only the New Stanton, Carlisle, and Middlesex interchanges did not follow this design, of which only the New Station interchange was intended to be permanent. Lighting was installed approaching interchanges, along with acceleration and deceleration lanes. The road also featured guardrails, consisting of steel panels attached to I-beams. Large exit signs were used and road signs had cat's-eye reflectors to increase visibility at night. Billboards were prohibited. In September 1940, the Pennsylvania Public Utility Commission ruled that trucks and buses would be allowed to use the highway.

Since the first section of the highway was built through a rural part of the state, food and gasoline were not readily available to motorists. Because of this, the commission decided to provide service plazas at 30-mile (48 km) intervals. The plazas would be constructed of native fieldstone, resembling Colonial-era architecture. In 1940, Standard Oil of Pennsylvania was awarded a contract for 10 Esso service stations along the turnpike. Eight of the service plazas would consist of service stations and a restaurant, while the plazas at the halfway point (in Bedford) would be larger. The South Midway service plaza (the largest) contained a dining room, lunch counter, lounge, and lodging for truckers; a tunnel connected it to the smaller North Midway plaza. The remaining service plazas were smaller, with a lunch counter. Food service at the plazas was provided by Howard Johnson's. After World War II, the food facilities were enlarged; service stations sold gasoline, repaired cars, and provided towing service.

Construction and opening

A view of the turnpike at an overpass in 1942

Before the first-section groundbreaking, in 1937, the turnpike commission sent workers to assess the former railroad tunnels. In September of that year, a contract was awarded to drain water from the tunnels. After this, workers cleared rock slides and vegetation from the tunnel portals before evaluating the nine tunnels' condition. It was decided that six of the nine former South Pennsylvania Railroad tunnels could be used for the roadway. The Allegheny Mountain Tunnel was in too poor a condition for use, and the Quemahoning and Negro Mountain tunnels would be bypassed with rock cuts through the mountains. The Quemahoning Tunnel had been completed and used by the Pittsburgh, Westmoreland and Somerset Railroad.

The Pennsylvania Turnpike groundbreaking was held on October 27, 1938, near Carlisle; Commission Chair Walter A. Jones thrust the first shovel into the earth. Turnpike construction was on a tight schedule because completion of the road was originally planned by May 1, 1940. After the groundbreaking, contracts for finishing the former South Pennsylvania Railroad tunnels, grading the turnpike's right-of-way, constructing bridges, and paving were awarded. By July 1939, the entire length of the turnpike was under contract.

The first work to begin on the road was grading its right-of-way, which involved a great deal of earthwork due to the mountainous terrain. Building the highway required the acquisition of homes, farms, and a coal mine by eminent domain. A tunnel was originally planned across Clear Ridge near Everett, but the turnpike commission decided to build a cut into the ridge. Building the cut involved bulldozers excavating the mountain and explosives blasting the rock. Concrete culverts were built to carry streams and roads under the highway in the valley floor. The Clear Ridge cut was 153 feet (47 m) deep (the deepest highway cut at the time) and was known as "Little Panama" after the Panama Canal. West of Clear Ridge, cuts and fills were built for the turnpike to pass along the southern edge of Earlston.

Considerable work was also involved in building the roadway up the three-percent grade at the east end of Allegheny Mountain, the steepest grade the turnpike traversed. The base of Evitts Mountain was blasted to carry the turnpike across Bedford Narrows along with US 30, the Raystown Branch of the Juniata River, and a Pennsylvania Railroad branch line. In New Baltimore, the turnpike commission had to purchase land from St. John's Church (which contained a cemetery); as part of the agreement, stairways were built on either side of the turnpike to provide access to the church.

Paving began on August 31, 1939. The roadway would have a concrete surface, and concrete was poured directly onto the earth with no gravel roadbed. Concrete batch plants were set up along the road to aid in paving. Interchange ramps were paved with asphalt. The paving operations led to a delay in the projected opening of the highway; by October 1939, the completion date was pushed back from May 1 to June 29, 1940, since paving could not be done during the winter. The commission rushed the paving, attempting to increase the distance paved from one to five miles (1.6 to 8.0 km) a day.

Completion was postponed to July 4, before being again postponed to late summer 1940 when rain delayed paving operations. Paving concluded by the end of the summer, and, on September 30, the turnpike commission announced that the road would open on October 1, 1940. Since the turnpike was opened on short notice, no ribbon-cutting ceremony was held.

On August 26, 1940, a preview of the highway was organized by Commission Chair Jones. It began the previous night with a banquet at The Hotel Hershey and proceeded west along the turnpike, stopping at the Clear Ridge cut before lunch at the Midway service plaza. The preview ended with dinner and entertainment at the Duquesne Club in Pittsburgh. That month, a military motorcade traveled portions of the turnpike.

The roadway took 770,000 short tons (700 kt) of sand, 1,200,000 short tons (1,100 kt) of stone, 50,000 short tons (45 kt) of steel, and more than 300,000 short tons (270 kt) of cement to complete. It was built at a cost of $370,000 per mile ($230,000/km) (equivalent to $6.3 million per mile ($2.5 million/km) in 2023). A total of 18,000 men worked on the turnpike; 19 died during its construction.

When the highway was under construction in 1939, its proposed toll was $1.50 (equivalent to $26.00 in 2023) for a one-way car trip; a round trip would cost $2.00 (equivalent to $34.00 in 2023). Trucks would pay $10.00 (equivalent to $172.00 in 2023) one way. Varying tolls would be charged for motorists who did not travel the length of the turnpike. Upon its opening in 1940, automobile tolls were set at $1.50 (equivalent to $26.00 in 2023) one way and $2.25 (equivalent to $38.00 in 2023) round trip. The tolls were to be used to pay off bonds to build the road and were to be removed when the bonds were paid. However, tolls continue to be charged to finance improvements to the turnpike system. The toll rate was about $0.01 per mile ($0.0062/km) (equivalent to $0.17 per mile ($0.11/km) in 2023) when the turnpike opened. The ticket system was used to pay for tolls. This toll rate remained the same for the turnpike's first 25 years; other toll roads (such as the New York State Thruway and the Ohio, Connecticut, and Massachusetts turnpikes) had a higher rate.

Pennsylvania Turnpike on opening

The Pennsylvania Turnpike opened at midnight on October 1, 1940, between Irwin and Carlisle; the day before the opening, motorists lined up at the Irwin and Carlisle interchanges. Homer D. Romberger, a feed and tallow driver from Carlisle, became the first motorist to enter the turnpike at Carlisle, and Carl A. Boe of McKeesport became the first motorist to enter at Irwin. Boe was flagged down by Frank Lorey and Dick Gangle, the first hitchhikers along the turnpike. On October 6 (the first Sunday after the turnpike's opening), traffic was heavy, with congestion at toll plazas, tunnels, and service plazas.

During its first 15 days of operation, the road saw over 150,000 vehicles. By the end of its first year, the road earned $3 million (equivalent to $51.1 million in 2023) in revenue from five million motorists, exceeding the $2.67 million (equivalent to $45.5 million in 2023) needed for operation and bond payments. With the onset of World War II, revenue declined due to tire and gas rationing; after the war, traffic again increased.

West portal of Blue Mountain Tunnel, viewed from Kittatinny Mountain Tunnel. Left photo from 1942; right photo from 2017.

When it opened, the turnpike became the first long-distance limited-access road in the United States. It provided a direct link between the Mid-Atlantic and Midwestern states and cut travel time between Pittsburgh and Harrisburg from nearly 6 to about 2.5 hours. The road was given the nicknames "dream highway" and "the World's Greatest Highway" by the turnpike commission and was also known as "the Granddaddy of the Pikes". Postcards and other souvenirs promoted the original stretch's seven tunnels through the Appalachians.

Western portal of the Rays Hill Tunnel in 2023

The highway was considered a yardstick by which limited-access highway construction would be measured. Commission Chair Jones called for more limited-access roads to be built across the country for defense purposes, and the turnpike was a model for a proposed national network of highways planned during World War II. The Pennsylvania Turnpike led to the construction of other toll roads, such as the New Jersey Turnpike and (eventually) the Interstate Highway System. It has been designated a National Historic Civil Engineering Landmark by the American Society of Civil Engineers.

1940s-1960s

70 mph speed limit on Pennsylvania Turnpike

1942

2014

The turnpike had no enforced speed limit when it opened except for the tunnels, which had a 35-mile-per-hour (56 km/h) speed limit. Some drivers traveled as fast as 90 mph (140 km/h) on the road. In 1941, speed limits of 70 mph (110 km/h) for cars and 50–65 mph (80–105 km/h) for trucks were enacted. During World War II, the turnpike adopted the national speed limit of 35 mph (56 km/h); after the war, the limit returned to 70 mph (110 km/h).

Westbound in Charlestown Township

Before the first section of the Pennsylvania Turnpike opened, the commission considered extending it east to Philadelphia, primarily for defense purposes. In 1939, the state legislature passed a bill allowing for an extension of the road to Philadelphia, which was signed into law by Governor Arthur James in 1940 as Act 11. The extension was projected to cost between $50 and $60 million in 1941 (equivalent to between $799 million and $959 million in 2023). Funding for the Philadelphia extension was in place in 1948. In July 1948, the turnpike commission offered $134 million (equivalent to $1.36 billion in 2023) in bonds to pay for the extension, which was projected to cost $87 million. The Philadelphia extension was to run from Carlisle east to US 202 in King of Prussia. From there, the extension would connect to a state-maintained freeway that would continue to Center City Philadelphia. Groundbreaking for the Philadelphia extension took place on September 28, 1948, in York County. Governor James H. Duff and Commission Chair Thomas J. Evans attended the ceremony. The extension would look similar to the original section of the turnpike but would use air-entrained concrete poured onto stone. Transverse joints on the pavement were spaced at 46-foot (14 m) intervals rather than the 77-foot (23 m) ones on the original portion. Because it traversed through less mountainous terrain, the extension did not require as much earthwork as the original section. It required the construction of large bridges, including those that cross the Susquehanna River and the Swatara Creek. To save money, the Susquehanna River Bridge was constructed with a four-foot-raised (1.2 m) concrete median and no shoulders. This extension of the turnpike would use the same style of overpasses as the original section; the steel deck bridge was also introduced. With the construction of the Philadelphia extension, the Carlisle interchange was closed and the Middlesex interchange with US 11 was realigned to allow for the new extension; it was renamed to the Carlisle interchange. On February 1, 1950, the Gettysburg Pike Interchange was opened. The extension's completion was delayed by weather and a cement workers' strike; it was to have been finished by October 1, 1950—the 10th anniversary of the opening of the first section. On October 23, 1950, the Philadelphia extension was previewed in a ceremony led by Governor Duff. The extension opened to traffic on November 20, 1950; the governor and Chair Evans cut the ribbon at the Valley Forge mainline toll plaza to the west of King of Prussia.

In September 1953, the speed limit on the portion of the highway between the Ohio state line and Breezewood was lowered to 60 mph (97 km/h) to reduce the number of accidents but returned to 70 mph (110 km/h) when the measure proved ineffective.

In 1941, Governor James suggested building a western extension to Ohio. That June, Act 54 was signed into law to build the extension. In 1949, the turnpike commission began looking into funding for this road, which would run from Irwin to the Ohio state line near Youngstown, Ohio, bypassing Pittsburgh to the north. That September, $77 million (equivalent to $781 million in 2023) in bonds were sold to finance construction of the western extension. Groundbreaking for the extension took place on October 24, 1949. It was scheduled to take place at the Brush Creek viaduct in Irwin with Governor Duff in attendance. Like the Philadelphia extension, the western extension required the building of long bridges, including those that cross the Beaver River and the Allegheny River. The overpasses along the road consisted of steel girder bridges and through plate girder bridges. Unlike the other segments, the concrete arch bridge was not used for overpasses, although it was used to carry the turnpike over other roads. On August 7, 1951, the roadway opened between the Irwin and Pittsburgh interchanges. Ohio Governor Frank Lausche led a dedication ceremony on November 26, 1951. The extension opened to the Gateway toll plaza near the Ohio state line on December 26, 1951. At the time, the highway ended in a cornfield. Traffic followed a temporary ramp onto rural local roads until the connecting Ohio Turnpike could be built. On March 1, 1952, the Beaver Valley Interchange was opened to traffic. On December 1, 1954, the Ohio Turnpike opened, and with it came an extension of the highway to the Ohio state line, at this point the temporary ramps onto the local roads were closed.

Westbound approaching the Mid-County interchange with I-476 in Plymouth Meeting

In 1951, plans to extend the turnpike east to New Jersey at the Delaware River to connect with the New Jersey Turnpike Connector were made. The construction of the Delaware River extension was approved by Governor John S. Fine in May of that year. A route for the extension, which would bypass Philadelphia to the north, was announced in 1952. It would cross the Delaware River on a bridge north of Bristol near Edgely, where it would connect to a branch of the New Jersey Turnpike. That September, the turnpike commission announced $65 million, equivalent to $599 million in 2023, in bonds would be issued to finance the project. Work on the Delaware River extension began on November 20, 1952; Governor Fine dug the first shovel into the earth at the groundbreaking ceremony. As a result of building the extension, the Valley Forge mainline toll plaza was located farther east at the connection to the Schuylkill Expressway and would then become the Valley Forge interchange toll plaza. The Delaware River extension included a bridge over the Schuylkill River that was built to the same standards as the Susquehanna River Bridge. The construction of the Delaware River bridge required an amendment to the Pennsylvania Constitution, which barred the state from forming compacts with other states. On August 23, 1954, the Delaware River Extension opened between King of Prussia and US 611 in Willow Grove. the segment to the Fort Washington Interchage opened on September 20, to the Philadelphia Interchange on October 27,the remainder of the road to the Delaware Valley Interchange opened on November 17, 1954.

In April 1954, $233 million (equivalent to $2.1 billion in 2023) in bonds were issued to finance the building of the Delaware River Bridge and the Northeast Extension. Groundbreaking for the Delaware River Bridge connecting the Pennsylvania Turnpike to the New Jersey Turnpike took place on June 26, 1954, in Florence, New Jersey. The steel arch bridge, which opened to traffic on May 23, 1956, was funded jointly by the Pennsylvania Turnpike Commission and the New Jersey Turnpike Authority. Pennsylvania Governor George M. Leader and New Jersey Governor Robert B. Meyner were present at the opening ceremony. A mainline toll barrier was built to the west of the bridge, marking the eastern end of the ticket system. Later that year, a new, machine based system was enacted for paying tickets, allowing for faster, more accurate fares than before. This bridge was originally six lanes wide. It contained no median, but one was later installed, and the bridge was reduced to four lanes. With the construction of the extensions and connecting turnpikes, the highway was envisioned to be a part of a system of toll roads stretching from Maine to Chicago. When the Delaware River Bridge was completed in 1956, a motorist could drive from New York City to Indiana on limited-access toll roads. That same year, the speed limit on the turnpike was reduced to 65 mph (105 km/h) for cars, buses, and motorcycles, with other vehicles limited to 50 mph (80 km/h). By 1957, it was possible to drive from New York City to Chicago without encountering a traffic signal. On the turnpike extensions, the service plazas were less frequent, larger, and further from the road. Gulf Oil operated service stations on the extensions, and Howard Johnson's provided food service in sit-down restaurants.

Signs at the turnpike entrance at Valley Forge showing I-76 and I-276 designations for the mainline and I-476 designation for the Northeast Extension

In August 1957, the Bureau of Public Roads added the roadway to the Interstate Highway System upon the recommendations of various state highway departments to include toll roads in the system. I-80 was planned to run along the turnpike from the Ohio state line to Harrisburg while I-80S would continue eastward toward Philadelphia. I-70 was also planned to follow the turnpike between Pittsburgh and Breezewood. At a meeting of the Route Numbering Subcommittee on the US Numbered System on June 26, 1958, it was decided to move the I-80 designation to an alignment further north while the highway between the Ohio state line and the Philadelphia area would become I-80S. I-70 was still designated on the turnpike between Pittsburgh and Breezewood. Between King of Prussia and Bristol, the turnpike was designated I-280. With the creation of the Interstate Highway System, restaurants and gas stations were prohibited along Interstate Highways. However, when it joined the system, the turnpike was grandfathered, allowing it to continue operating its service plazas. That same year, the turnpike commission began to install median barriers at curves and high-accident areas.

In July 1959, a minimum speed of 35 mph (56 km/h) was established.

1960s–1990s

By the early 1950s, it was apparent that the original concrete driving surface was in poor shape. This was caused by excessive transverse-joint spacing and the lack of gravel between earth and concrete. Because of this, a project began in the summer of 1954 to layer the original turnpike segment between Irwin and Carlisle with a 3-inch (7.6 cm) layer of asphalt. During the work, traffic was restricted to two lanes across one roadway while the other was surfaced. The first stretch to be rehabilitated was the 21-mile (34 km) stretch east of the Sideling Hill Tunnel. Repaving the rest of the roadway was completed by September 8, 1962.

Interstate 280
Location	Upper Merion Township–Bristol Township
Length	32.65 mi (52.55 km)
Existed	1958–February 1964

In April 1963, the state of Pennsylvania proposed renumbering I-80S to I-76 and I-280 to I-276 because the spurs of I-80S did not connect to I-80 in northern Pennsylvania. The renumbering was approved by the Federal Highway Administration (FHWA) on February 26, 1964. With this renumbering, the turnpike would carry I-80S between the Ohio state line and Pittsburgh, I-76 between Pittsburgh and King of Prussia, I-70 between New Stanton and Breezewood, and I-276 between King of Prussia and Bristol.

The original New Stanton interchange, as seen in this 1940s photograph

In October 1963, work began on a $1.6 million project to replace the New Stanton interchange. The old configuration, which had served US 119 and required left turns across traffic on grade level ramps, resulted in the interchange having become a chronic bottleneck. The new interchange would be a standard trumpet interchange, and serve a newly built stretch of I-70. The ramps were opened to traffic on November 12, 1964, at which point the old ramps closed permanently. Some of the old grounded ramps are still extant, though are only used for storage.

In September 1965, the minimum speed limit was raised to 40 mph (64 km/h).

The roadway's median, while initially thought to be wide enough, was considered obsolete by 1960. Because of this, 100 miles (160 km) worth of median barrier began to be constructed across the original turnpike, as well as the Ohio extension. Work was completed in December 1965 at a cost of $5 million (equivalent to $36.9 million in 2023).

The Laurel Hill bypass in 2017.

As traffic levels increased, bottlenecks at the two-lane tunnels on the original stretch became a major problem. By the end of the 1950s, traffic jams formed at the tunnels, especially during the summer months in the middle of the year. In 1959, four senators urged state officials to work with the turnpike commission to study ways to reduce the traffic jams. The same year, the commission began studies aimed at resolving the traffic jams at the Laurel Hill and Allegheny Mountain tunnels; studies for the other tunnels followed. At the conclusion of the studies, the turnpike commission planned to make the entire turnpike at least four lanes by either adding a second tube at the tunnels or bypassing them. The new and upgraded tunnel tubes would feature white tiles, fluorescent lighting, and upgraded ventilation. The turnpike commission announced plans to build a second bore at the Allegheny Mountain Tunnel and a four-lane bypass of the Laurel Hill Tunnel in 1960. A Laurel Hill bypass was planned because construction would be quicker and traffic relieved cheaper than it would by boring another tunnel. In June 1962, the commission approved these two projects.

That August, $21 million, equivalent to $162 million in 2023, in bonds were sold to finance the two projects. The Laurel Hill bypass was constructed as a deep cut to the north; the new section would feature a wide median and truck climbing lanes. It would require use of explosives to create a 145-foot-deep (44 m) cut into the mountain. Groundbreaking for the new alignment took place on September 6, 1962, the same day boring the second tube at Allegheny Mountain Tunnel also began. The former South Pennsylvania Railroad tunnel was considered for reuse as a twin of the latter but was again rejected because of its poor condition. The Laurel Hill bypass opened to traffic on October 30, 1964, at a cost of $7.5 million (equivalent to $56.3 million in 2023). On March 15, 1965, the new Allegany Mountain Tunnel opened to traffic, after which the original tube was closed to allow renovations to be made. It reopened on August 25, 1966. The construction of the second tube at Allegheny Mountain cost $12 million (equivalent to $86.1 million in 2023).

In 1969, $3.2 million worth of improvements were completed to the Ohio Extension. These included building new ramps serving I-283 and PA 283 at Harrisburg East, in addition to widening the gateway toll plaza from 8 to 10 collection lanes the and Pittsburgh interchanges to 10 lanes.

Starting in 1953, it became apparent that the turnpike was prone to serious accidents. Because of this, the PTC began installing steel barriers at curves and high-accident areas in 1957. By 1970, the entire roadway had barriers installed.

The Abandoned Pennsylvania Turnpike in 2023

With the Laurel Hill bypass opened and the twined Allegheny Tunnel nearly complete, twinning or bypassing to the five other two lane tunnels became the focus. In 1965, the turnpike commission announced plans to build second tubes at the Tuscarora, Kittatinny, and Blue Mountain tunnels, in addition to a 13.5-mile (21.7 km) bypass of the Rays Hill and Sideling Hill tunnels. A bypass of these two tunnels was considered in the 1930s but, at the time, was determined to be too expensive. An early 1960s study concluded that a bypass would be the best option to handle traffic at Rays Hill and Sideling Hill. This bypass of the two tunnels would have a 36-foot-wide (11 m) median with a steel barrier. The commission sold $77.5 million (equivalent to $556 million in 2023) in bonds in January 1966 to finance this project. Construction of the bypass of the Rays Hill and Sideling Hill tunnels involved building a cut across both hills. The new alignment began at the Breezewood interchange, where a portion of the original turnpike was used to access US 30. In building the cut across Rays Hill, a portion of US 30 had to be realigned.

The cut over Sideling Hill passes over the Sideling Hill Tunnel. The new alignment ends a short distance east of the Cove Valley service plaza on the original segment. The turnpike bypass of Rays Hill and Sideling Hill tunnels opened to traffic on November 26, 1968. When the highway was realigned to bypass the Rays Hill and Sideling Hill tunnels, the Cove Valley service plaza on the original section was closed and replaced with the Sideling Hill service plaza (the only service plaza on the main turnpike serving travelers in both directions). After traffic was diverted to the new alignment, the former stretch of roadway passing through the Rays Hill and Sideling Hill tunnels became known as the Abandoned Pennsylvania Turnpike. The turnpike commission continued to maintain the tunnels for a few years but eventually abandoned them. The abandoned stretch deteriorated; signs and guardrails were removed, pavement started crumbling, trees grew in the median, and vandals and nature began taking over the tunnels. The turnpike commission still performed some maintenance on the abandoned stretch and used it for testing pavement marking equipment.

In 2001, the turnpike commission turned over a significant portion of the abandoned section to the Southern Alleghenies Conservancy; bicycles and hikers could use the former roadway. The abandoned stretch of the turnpike is the longest stretch of abandoned freeway in the United States. Meanwhile, studies concluded that a parallel tunnel was the most economical option at the Tuscarora, Kittatinny, and Blue Mountain tunnels. Work on the new tube at the Tuscarora Mountain Tunnel began on April 11, 1966, while construction began at the Kittatinny and Blue Mountain tunnels a week later. The parallel tubes at these three tunnels would open on November 26, 1968. The original tubes were subsequently remodeled. Both the new and remodeled tunnels would have fluorescent lighting, white tile walls, and 13-foot-wide (4.0 m) lanes. The portals of the new tunnels were designed to resemble those of the original tunnels. In October 1970, a new Breezewood interchange was opened, the new exit, which utilized part of the original turnpike segment, replaced the preexisting Breezewood interchange, which had closed alongside the stretch of road in 1968. That same month, reconstruction of the original Tuscarora Mountain Tunnel was completed. Work on refurbishing the original Kittatinny and Blue Mountain tunnels was finished on March 18, 1971. With the completion of these projects, the entire length of the mainline highway was at least four lanes wide, thus upgrading it to the greater interstate standards.

In 1968, the turnpike commission proposed converting the section of the road between Morgantown and the Delaware River Bridge from a ticket to a barrier system. The project was canceled in 1971 due to a decline in revenue caused by the completion of I-80.

Interstate 80S
Location	North Beaver Township–Upper Merion Township
Existed	1958–October 1972

In 1971, the state of Ohio made plans to eliminate I-80S, replacing it with a realigned I-76. The state of Pennsylvania disagreed with the change and recommended that I-80S become I-376 instead. The Pennsylvania government later changed its mind and supported Ohio's plan to renumber I-80S as I-76. In December of that year, the change was approved by the American Association of State Highway Officials. As a result, I-76 would follow the turnpike between the Ohio state line and King of Prussia. This change took effect on October 2, 1972.

In 1969, the turnpike commission announced plans to widen the turnpike. It proposed doubling the number of lanes from four to eight; the portion in the Philadelphia area was to be 10 lanes wide. Cars and trucks would be carried on separate roadways under this plan. They had also proposed a new interchange with I-79 in Carpenter town. The roadway would also have had a 80-mile-per-hour (130 km/h) speed limit and holographic road signs. This widening would have kept much of the routing intact, but significant reconstruction was proposed between the Allegheny Mountain and Blue Mountain tunnels. Because of the $1.1-billion (equivalent to $5.76 billion in 2023) cost and the 1973 oil crisis that resulted in the imposition of a 55-mile-per-hour (89 km/h) speed limit, this plan was not implemented.

By the 1970s, the Pennsylvania Turnpike started to see a decline in the volume of traffic because of the opening of I-80, which provided a shorter route across the northern part of the state, and the 1973 oil crisis, which led to a decline in long-distance travel.

With the passage of the 1974 National Maximum Speed Law, the speed limit on the turnpike was reduced to 55 mph (89 km/h).

Due to the widening and relocation of US 222 to a new four-lane freeway, construction of a new Reading–Lancaster Interchange was proposed in 1970, it would replace the existing one. This was opened on April 10, 1974, at which point the original Reading interchange was closed.

In the late 1970s, the turnpike commission proposed constructing truck climbing lanes east of the Allegheny Mountain Tunnel near New Baltimore and near the Laurel Hill Bypass. These were completed on December 2, 1981. The project, which also involved the construction of 2.2 miles (3.5 km) worth of eastbound roadway and widening of the westbound roadway from two to three lane. This came alongside $70 million worth of expansions and renovations to the Irwin, New Stanton, Donegal, Somerset, and Carlisle interchanges.

On September 10, 1983, the Blue Mountain Interchange's old toll plaza, the last one which dated back to 1940, was closed when the plaza was expanded from a two lane plaza. The old hexagon shaped booth was donated to the Smithsonian Institution.

Eastbound approaching the Willow Grove interchange with PA 611

By the early 1980s, a significant portion of the Philadelphia Extension had become a congested bottleneck. In 1983, funding was approved to widen the turnpike to six lanes between the Valley Forge and Philadelphia interchanges. This planned project was put on hold because of disagreements between Governor Dick Thornburgh and the turnpike commission members and differences between the commissioners. The Pennsylvania Legislature approved the project in 1985; the road would be widened between the Norristown and Philadelphia interchanges. Construction on the widening began on March 10, 1986, with improvements to the Fort Washington, Willow Grove, and Philadelphia interchanges completed later that year. The rest of the widening was completed on November 23, 1987, with a ribbon-cutting at the Philadelphia interchange. The widening project cost $120 million (equivalent to $629 million in 2023).

Studies to eliminate toll takers for handing out tickets began in 1982. Following the studies determining they would reduce congestion, ticket machines replaced human workers on July 22, 1987. Following this, in 1988, tandem toll booths were added to the Valley Forge interchange plaza, with tandem booths following at the Willow Grove Interchange in 1989.

The turnpike formerly had a call box every mile (1.6 km) for its entire length. Call boxes were first installed between New Stanton and New Baltimore in December 1988, and, in 1989, call boxes were extended along the length of the highway.

1990s–present

Eastbound past the Harrisburg East interchange with I-283/PA 283

The turnpike commission celebrated the highway's 50th anniversary in October of 1990. Over $300,000 (equivalent to $618,462 in 2023) was spent to promote the turnpike through various means including a videotape, souvenirs, and a private party attended by politicians and companies that work with the turnpike.

Concurrent with construction of the Beaver Valley Expressway, the New Castle Interchange was also built to serve it. This, alongside the section of that roadway from US 422 to PA 51, was opened to traffic on November 8, 1991.

A new interchange to serve the New Cumberland Defense Depot near Harrisburg was planned in the late 1980s. In September 1992, the turnpike commission scrapped the project because it would instead build a connector road to the depot between PA 114 and Old York Road that would parallel the turnpike.

Plans to build a replacement Plymouth Meeting interchange connecting to the north end of I-476 (Mid-County Expressway) was mad in the late 1980s, the turnpike commission approved a contract to build the interchange in March 1989. The new ramps would replace the preexisting Plymouth Meeting interchange, which had only served the south end of the Northeast Extension. That June, a losing bidder decided to challenge the turnpike commission, saying it violated female and minority contracting rules regarding the percentage of these employees that were used for the project. Under this rule, bidders were supposed to have at least 12 percent of contracts to minority-owned companies and at least four percent to female-owned companies. The losing bidder had 12.4 percent of the contracts to minority companies and 4.2 percent to female-owned companies while the winning bidder had 6.1 percent and 3.7 percent, respectively. The turnpike commission decided to rebid the contract but was sued by the original contractor. This dispute delayed the construction of the interchange. The contract was rebid in November 1989 after the Supreme Court of Pennsylvania permitted it. The interchange between I-476 and the turnpike mainline was completed in November 1992; the ramps to the Northeast Extension opened a month later. An official ribbon-cutting took place on December 15, 1992.

In 1990, an interchange was proposed with PA 743 between Elizabethtown and Hershey, but a study in 1993 determined that it would not improve traffic flow on area roads.

In 1995 the speed limit was raised to 65 mph (105 km/h), except for urban areas with a population greater than 50,000; the latter retained the 55-mile-per-hour (89 km/h) speed limit.

In September 1990, a replacement of the Morgantown interchange was competed. The new ramps served I-176, unlike the old configuration, which had served PA 10, the latter was then closed to through traffic. The overhead lights at the new exit were considered a nuisance by residents who lived near it. It would not be until 1996 that the connecting link with I-176 opened to traffic, however.

In early 1999, the PTC began printing coupons on the back of toll receipts, primarily for use by business owners.

Westbound in Upper Allen Township

Construction began in 1998 to improve the bridge over the Schuylkill River in Montgomery County. The work involved building a new bridge adjacent to the existing bridge; the new bridge was wide enough to accommodate a future widening to six lanes. This project was completed in 2000.

In October 2000, the turnpike commission announced the road would be switching from sequential exit numbering to distance-based exit numbering. At first, both exit numbers would exist, but the old numbers would be phased out later. Work began on posting the new exit numbers in 2001.

In June 1998, the PTC began rebuilding the section of roadway between mileposts 94 and 99 near the Westmoreland/Somerset County line at the cost of $24 million. Work was completed in 2000.

In 2001, the PTC rebuilt the Gateway toll plaza to add modern amenities and more toll lanes.

The westbound Virginia Drive slip ramp in Fort Washington, Pennsylvania

An electronic toll collection system was first proposed in 1990 where a motorist would create an account and use an electronic device which would be read from an electronic tollbooth; the motorist would be billed later. The multi-state electronic tolling system E-ZPass was planned to go into effect by 1998; Additionally, in 1996, the turnpike commission considered adding slip ramps in the Philadelphia area in which electronic toll collection technology would be used. Construction began on a westbound E-ZPass-only slip ramp at Virginia Drive (exit 340) in Fort Washington in early 2000; it opened on December 2, 2000, having cost $5.1 million, equivalent to $8.58 million in 2023. That same day, E-ZPass debuted on the turnpike between Harrisburg West and the Delaware River Bridge. By December 15, 2001, E-ZPass could be used on the entire length of the Pennsylvania Turnpike. on December 14, 2002, the system was introduced to commercial vehicles.

Plans were made in 1993 to build a direct interchange between the turnpike and I-79 in Cranberry Township, Butler County. A contract was awarded to build this interchange in November 1995. In 1997, transportation officials agreed upon a design for the interchange. The project also included moving the western end of the ticket system to a new toll plaza in Warrendale. The interchange project was delayed by a dispute with Marshall and Pine townships in Allegheny County, who wanted to prevent construction of the toll plaza as they thought it would cause noise, air, and light pollution. Marshall Township eventually agreed to allow the toll plaza be built. Groundbreaking for the new interchange took place on February 22, 2002. The westbound Butler service plaza was closed because the Warrendale toll plaza was to be located at its site. On June 1, 2003, the plaza opened and the Gateway toll plaza became a flat-rate toll plaza, while all the exit toll plazas west of Warrendale closed. The direct interchange between the turnpike and I-79, connecting to US 19, opened on November 12, 2003. The project cost $44 million (equivalent to $69.9 million in 2023). In June 2004, the Express E-ZPass lanes were competed at the Warrendale toll plaza, which allowed motorists to travel through the toll plaza at highway speeds.

Beginning November 25, 2004, turnpike management personnel collected flat-rate cash passenger tolls of $2 and commercial tolls of $15 on the ticketed system, while E-ZPass customers were charged the lesser amount of the toll or the flat rate.

In April 2005, the turnpike commission approved raising the speed limit to 65 mph (105 km/h) for the entire length of the turnpike, excluding tunnels, mainline toll plazas, and the winding portion near the Allegheny Mountain Tunnel, which retained the 55-mile-per-hour (89 km/h) limit.

Eastbound at the Valley Forge interchange, where I-76 splits from the turnpike and I-276 begins

In 2000, the turnpike commission announced plans to build a new bridge, a segmental concrete bridge wider than the original, over the Susquehanna River. In 2004, work began on building the new, six-lane bridge which cost $150 million (equivalent to $232 million in 2023). On May 16, 2007, a ribbon-cutting took place to mark the completion of the westbound direction of the bridge, which opened to traffic the following day. The eastbound direction of the bridge opened a month later. In 2004, proposals to widen the highway to six lanes between Downingtown and Valley Forge were made. In 2007, the western terminus of the widening project was scaled back from Downingtown to the proposed PA 29 slip ramp. Plans for the widening were presented to the public in 2009. Later that year, the widening was put on hold because of engineering problems. The widening plans resumed in 2010. Work was due to begin in 2013, with completion in 2015. In October 2012, the project was postponed a year because of delays in the approval of permits.

The stairs to St. John's Church in New Baltimore in 2010

In December 2005, the turnpike commission announced plans to rebuild the Gateway toll plaza into an eastbound-only, express E-ZPass plaza. This project, which would begin in 2006, in 2006 in order to reduce congestion. The Express E-ZPass lanes at Gateway opened in July 2007.

In December 2005, the PTC began a prudent to improve the Gettysburg Pike interchange. It involved widening the toll plaza, expanding the utility building, rebuilding the roadway, and associated structures including replacement and rehabilitating bridges within the interchange and on the Turnpike. The project was completed in October 2007 at the cost of $29 million.

Plans were announced to build a new pair of bridges over the Allegheny River in 2005, hitch would replace the existing deck truss bridge. Work began in May 2007, and a dedication ceremony was held on October 23, 2009. The bridges, which cost $194 million (equivalent to $268 million in 2023), opened to traffic the following day, and the old bridge was demolished on July 13, 2010.

Work on the eastbound slip ramp at PA 132 (exit 352) in Bensalem Township began in 2009; the ramp opened on November 22, 2010. This slip ramp, which cost $7.4 million (equivalent to $10.1 million in 2023), has access to and from the eastbound direction of the turnpike and was built to provide improved access to Parx Casino and Racing. While all slip ramps were initially reserved for E-ZPass users, they opened to all traffic following the conversion of the turnpike to cashless tolling in 2020. Other slip ramps were planned in the Philadelphia area at PA 29 near the Great Valley Corporate Center and at PA 252 in Valley Forge in the 1990s. Residents opposed the PA 29 (exit 320) ramp, fearing it would spoil the rural area. In 1999, the turnpike commission canceled plans to build a slip ramp at PA 252 and instead focused on building one at PA 29. The turnpike commission approved funding for the PA 29 ramp in 2002, but the project was put on hold in 2009 because of engineering and design problems in widening the adjacent portion of the turnpike. It was announced that the turnpike commission would approve construction of the slip ramp at PA 29 in August 2010, and construction began in March 2011. The interchange, which has access to and from both directions of the turnpike, opened on December 11, 2012; Governor Tom Corbett cut the ribbon.

Plans were made to widen the highway to six lanes between Irwin and New Stanton in 2005. Work on the project began in January 2006; it added a third lane in each direction, replaced several bridges, and realigned a portion of the turnpike and was completed in November 2011. As part of the project, in January 2007, the Hempfield service plaza was permanently closed.

Westbound past the Virginia Drive interchange in Fort Washington

In November 2006, Governor Ed Rendell and former Pennsylvania House Speaker John Perzel raised the idea of leasing the turnpike longterm to a private group to raise money to improve other infrastructure in the state. Such a lease was speculated to raise up to $30 billion (equivalent to $43.6 billion in 2023) for the state. In October 2007, 34 companies submitted 14 proposals to lease the turnpike. On May 19, 2008, a record $12.8-billion (equivalent to $18.1 billion in 2023) proposal by Abertis, a Spain-based firm, and Citigroup in New York City to lease the turnpike was submitted. The consortium withdrew the offer on September 30, 2008, as they reasoned the proposal would not be approved in the state legislature.

A study began in 1999 to widen the road to six lanes between Valley Forge and Norristown. In October 2004, work began on widening this stretch of road, which was completed in November 2008 at a cost of $330 million (equivalent to $459 million in 2023).

On July 22, 2014, the speed limit increased to 70 mph (110 km/h) between the Blue Mountain and Morgantown interchanges.

On March 15, 2016, the PTC approved raising the speed limit on the remainder of the turnpike to 70 mph (110 km/h), excluding sections that are posted with a 55-mile-per-hour (89 km/h) speed limit. On May 3, 2016, the speed limit increased to 70 mph (110 km/h) on the 65-mile-per-hour (105 km/h) sections of the toll road. The speed limit remains 55 mph (89 km/h) at construction zones, the tunnels, mainline toll plazas, the winding portion near the Allegheny Mountain Tunnel, and the section between Bensalem and the Delaware River Bridge.

In 2015, a pilot program started at exit 189 (Willow Hill) that used automated payment machines that accept credit and debit cards. In October 2016, the turnpike began accepting credit cards as payment at all cash toll booths.

The Pennsylvania Turnpike used traffic lights as feedback signals for E-ZPass users since it was launched on the roadway in 2001. On March 17, 2017, the PTC announced that they would begin removing the feedback signals as part of upgrading the toll equipment; the feedback signals were removed because they do not conform to federal signage guidelines.

In September 2017, the turnpike commission began removing the call boxes due to increased mobile phone usage making the call boxes obsolete.

The split where the Pennsylvania Turnpike westbound exits I-95 southbound in Bristol Township

In 2019, the turnpike launched a smartphone app for paying tolls.

In 2007, as part of a project to widen a section of the turnpike in Somerset and Bedford counties to six lanes that will last from 2016 to 2020, the turnpike commission announced that it would remove the steps leading to St. John's Church in New Baltimore because they are a safety hazard.

Construction to widen the section between mile markers 102 and 109 west of Somerset (with a couple small curve realignments) began in January 2021 and was substantially completed in August 2024.

In September 2013, the PTC began a minor project to replace many of the bridges between mileposts 12 and 14. This project, competed in November 2017, allowed for a future widening from four to six lanes. With the first phase competed, in December 2022, the PTC began the second phase, which would construct a six lane replacement of the Beaver River Bridge, as well as reconstruction of the Beaver Valley interchange form a full trumpet into a nonstandard slip interchange. Work is expected to be competed in September 2027, at the total cost of $292 million.

The widening project between the PA 29 and Valley Forge interchanges is being split into two phases, one running between the PA 252 overpass and the Valley Forge interchange and the other between the PA 29 interchange and the PA 252 overpass. Construction on widening the section between the PA 252 overpass and the Valley Forge interchange began on September 27, 2021, with completion expected in May 2025. In early 2023, construction began on widening the turnpike from the Downingtown interchange east to the Valley Hill Road overpass, with completion planned for 2027.

Future

In 2013, Montgomery County officials announced they were considering adding more slip ramps along the turnpike to ease traffic congestion. The Pennsylvania Turnpike Corridor Reinvestment Project was released in 2015, with the project planning to construct additional interchanges along the Pennsylvania Turnpike in Montgomery County in order to revitalize business parks adjacent to the roadway. Proposed locations for new interchanges include PA 63 near Willow Grove, Henderson Road in Upper Merion Township, and Lafayette Street/Ridge Pike near Norristown and Plymouth Meeting. In addition, there are plans to add eastbound ramps at the existing Virginia Drive interchange, add additional ramps at the Valley Forge interchange connecting to First Avenue and Moore Road in King of Prussia, add an additional ramp at the Fort Washington interchange connecting to Commerce Drive, and modernize the Willow Grove interchange. Construction of the extension of Lafayette Street began in 2013 and was completed in 2014. On January 7, 2015, the turnpike commission committed $45 million (equivalent to $56.6 million in 2023) to building this interchange. The turnpike commission's Fiscal Year 2017 Capital Plan included $66 million (equivalent to $80.7 million in 2023) for the interchange at Lafayette Street. The design phase of the interchange began in 2017, with preliminary engineering taking place in 2018 and 2019. Construction of the interchange with Lafayette Street is expected to begin in 2027 and be completed in 2029. A slip ramp was also planned in 2000 as part of a revitalization plan to connect to Lafayette Street with the turnpike in Norristown. The project would involve extending Lafayette Street to the new ramp. This proposed slip ramp is projected to cost $160 million (equivalent to $269 million in 2023). Montgomery County officials have proposed a surcharge for the new exit in to help pay for the project. Work on engineering and environmental approval for the extension of Lafayette Street occurred in 2008, and acquisition of land began in 2011.

Plans to build a direct interchange between the Pennsylvania Turnpike and I-95 in Bristol Township to allow a connection between the portions of I-95 in Pennsylvania and along the New Jersey Turnpike were first proposed in 1978. The two roads did not have an interchange because earlier laws—since repealed—prohibited federal funds from being used to build connections to toll roads. In 1982, the federal government mandated that the interchange be built in Pennsylvania. A gap existed in I-95 because of the unbuilt Somerset Freeway segment in central New Jersey. Under the plan, I-95 would be rerouted to follow the turnpike between the new interchange and the New Jersey state line. In addition, the interchange would serve as the new terminus of an extended I-295. The area's residents, who thought the interchange would lead to a decline in their quality of life, opposed this plan. An environmental impact statement (EIS) was released in 2003. The interchange received environmental approval in 2004, the preliminary design was completed in 2008, and the final design followed. The project involved building a high-speed interchange between the two roadways. The turnpike commission will also widen the existing four-lane road to six lanes east of the Bensalem interchange. A new toll plaza was built east of the Street Road interchange at Neshaminy Falls to mark the eastern end of the ticket system that consists of high-speed E-ZPass lanes along with ticket and cash booths, and the former Delaware River Bridge toll barrier was converted to a westbound all-electronic facility. A new bridge will also be built over the Delaware River. Work on the project began in late 2010; the replacement of two bridges over the turnpike was completed in 2011.

Groundbreaking for the interchange with I-95 took place on July 30, 2013, with Governor Corbett in attendance. Construction of the first stage of the interchange began in late 2014. The flyover ramps between northbound I-95 and the eastbound turnpike and between the westbound turnpike and southbound I-95 opened on September 22, 2018. Work on the new mainline toll plaza and widening of the turnpike between I-95 and the Delaware River also began in 2013, with completion in 2016. The connector was finished in 2018 and completed I-95, which runs from Florida north to Maine. That highway is part of the Interstate Highway System and serves over 110 million people in over 10 percent of the total US land area. The development began as part of the Federal-Aid Highway Act in 1956. Additionally, I-95 was widened, and exit 42 ramp to US 13 was rebuilt into an at-grade intersection, with the tolls also being removed. Long-term plans call for the construction of missing movements between the turnpike, I-95, and I-295, along with the widening of the turnpike between the Bensalem interchange and I-95. Plans have also been made for a six-lane replacement of the Delaware River Bridge, which is expected to begin construction in 2025 at the earliest. The first stage of the project, which includes the new toll plaza, widening, and the flyover ramps between I-95 and the turnpike, is to cost $420 million. The flyover ramps are expected to cost $142.9 million, with $100 million coming from federal funds and the remainder from the turnpike commission. The PTC is borrowing money from foreign investors in order to provide funding for the project. The commission entered into a partnership with the Delaware Valley Regional Center (DVRC) in 2014 to raise half of the funds needed to construct the interchange. The EB-5 visa program will allow the commission through the DVRC to save about $35 million over traditional borrowing costs over five years. The remaining stages of the project are unfunded, with a projected total cost of $1.1 billion for the entire project.

In 1996, a study on improving the Allegheny Mountain Tunnel by either building another tube or by constructing a bypass was carried out. Based on the study, the turnpike commission planned to replace the deteriorating tunnel with a cut through the mountain. The plans were put on hold in 2001 because it would cost $93.7 million (equivalent to $154 million in 2023). It resurrected the project in 2009. The nearby Mountain Field and Stream Club prefers that the tunnels be improved or a new tube built rather than building the bypass. These improvements are needed because the Allegheny Mountain Tunnel is narrow and deteriorating, with disintegrating ceiling slabs and outdated lighting and ventilation.

On October 22, 2013, the PTC announced plans to replace the tunnels, the older of which was 73 years old that year, with either new tunnel or a bypass due to the age and condition of the 1940 tunnel and the need for additional capacity. Approximately 11 million vehicles drive through the tunnel every year. On December 24, 2014, the PTC announced it was going forward with plans to replace the Allegheny Mountain Tunnel. Six options are being considered, three of which would include building bypasses via rock blasting (as was done with the Laurel Hill Tunnel) while the other three would involve boring two new tunnels, presumably three lanes each to accommodate the PTC's long-term plans to widen the entire mainline turnpike to six lanes except at the existing tunnels. If the PTC goes through with building new tunnels, the existing Allegheny Mountain Tunnels would be shut down. Although the projected costs for building a bypass would be less than half that of boring new tunnels and would also require $3 million less for annual maintenance on each tunnel, the Mountain Field and Stream Club, a local hunting group that owns 1,000 acres (400 ha) of land around the tunnel, opposed the bypass options; the group had also opposed plans to replace the tunnels in 2001. In February 2020, the PTC decided that the tunnel would be bypassed via a new roadway to the south. Such a plan is expected to be cheaper and have a lesser environmental impact than constructing a new tunnel. The project is currently under environmental review; design is expected to take three to four years, and construction will take another three years. The bypass will cost $332.4 million.

On July 16, 2019, the PTC voted to allocate $30 million to its 10-Year Capital Plan, for a new interchange from the turnpike to PA 130 in Penn Township, between current exits 57 and 67. According to a Southwestern Pennsylvania Commission study, PA 130 would need to be widened to account for the additional traffic, costing about $38 million and bringing the total project cost to about $68 million. The interchange would utilize cashless tolling, either through the electronic E-ZPass system or a camera system, in which the turnpike would take a photo of the driver's license plate and mail them an invoice.

The project would also need coordination between the turnpike commission and PennDOT, which maintains PA 130. The project is supported by the Westmoreland County Chamber of Commerce. On October 28, 2021, it was announced that design work on the interchange would begin. The interchange between the turnpike and PA 130 is projected to be completed in 2026.

On September 24, 2024, the PTC announced plans to widen the stretch of roadway between mileposts 160 and 163 from four to six lanes. This would also involve reconstruction of the Breezewood interchange to add a direct connection between the turnpike and I-70. The project is planned to begin the preliminary design phase in 2025, with construction underway by 2027.

Exit list

County	Location	mi	km	Old exit	New exit	Name	Destinations	Notes
Lawrence	North Beaver Township	0.00	0.00	–	–		I-76 west / Ohio Turnpike west – Ohio	Continuation into Ohio; western end of I-76 overlap
		1.43	2.30	Gateway Toll Gantry (eastbound only; E-ZPass or toll-by-plate)
Beaver	Big Beaver	10.70	17.22	1A	10	New Castle	I-376 Toll – New Castle, Pittsburgh	I-376 exit 26
		12.87	20.71	2	13	Beaver Valley	PA 18 – Ellwood City, Beaver Falls
	Beaver River	13.0– 13.3	20.9– 21.4	Beaver River Bridge
Butler	Cranberry Township	28.47	45.82	3	28	Cranberry	I-79 / US 19 – Pittsburgh, Erie	I-79 exit 77; access to Old Economy Village State Historic Site; formerly called the Perry Highway Interchange
Allegheny	Marshall Township	31.00	49.89	Warrendale Toll Gantry (western end of closed toll system)
	Hampton Township	39.10	62.93	4	39	Butler Valley	PA 8 – Pittsburgh, Butler	Formerly called the North Pittsburgh Interchange
	Harmar Township	47.73	76.81	5	48	Allegheny Valley	To PA 28 – New Kensington, Pittsburgh	Access via Freeport Road
	Allegheny River	47.8– 48.2	76.9– 77.6	Allegheny River Bridge
	Plum	49.30	79.34	Oakmont Plum Service Plaza (eastbound)
	Monroeville	56.44	90.83	6	57	Pittsburgh	I-376 west / US 22 / US 22 Bus. west – Pittsburgh, Monroeville	I-376 exit 85; eastern terminus of I-376; US 22 Bus. not signed; access to North Shore Destinations
Westmoreland	Penn Township	62.84	101.13		62	SR 130	PA 130	Proposed interchange; construction expected to start in 2035
	North Huntingdon Township	67.22	108.18	1 7	67	Irwin	US 30 – Irwin, Greensburg, McKeesport	Signed for Greensburg eastbound, McKeesport westbound
	New Stanton	75.39	121.33	2 8	75	New Stanton	I-70 west to US 119 / PA Turnpike 66 north – Greensburg, Wheeling, WV	I-70 exit 58; western end of I-70 overlap; access to Washington, PA and Columbus, OH via I-70 west; access to Connellsville via US 119; access to Delmont via PA 66
	Hempfield Township	77.60	124.89	New Stanton Service Plaza (westbound)
	Donegal Township	90.69	145.95	3 9	91	Donegal	PA 31 to PA 711 – Ligonier, Uniontown
Somerset	Somerset	109.91	176.88	4 10	110	Somerset	PA 281 to US 219 – Somerset, Johnstown	PA 281 not signed; access to Flight 93 National Memorial
	Somerset Township	112.30– 112.40	180.73– 180.89	North Somerset Service Plaza (westbound) South Somerset Service Plaza (eastbound)
	Stonycreek–Allegheny township line	122.7– 123.9	197.5– 199.4	Allegheny Mountain Tunnel
Bedford	Bedford Township	145.50	234.16	5 11	146	Bedford	US 220 Bus. to I-99 north / US 220 – Bedford, Altoona	US 220 Bus. not signed; I-99 exit 1; access to Blue Knob State Park, Shawnee State Park, and Cumberland, MD
		147.30	237.06	North Midway Service Plaza (westbound) South Midway Service Plaza (eastbound)
	East Providence Township	161.50	259.91	6 12	161	Breezewood	I-70 east to US 30 – Everett, Baltimore	Eastern end of I-70 overlap; Everett not signed eastbound
Fulton	Taylor Township	172.30	277.29	Sideling Hill Service Plaza (both directions)
	Dublin Township	179.44	288.78	7 13	180	Fort Littleton	US 522 – McConnellsburg, Mount Union
Huntingdon–Franklin county line	Dublin–Metal township line	187.3– 188.3	301.4– 303.0	Tuscarora Mountain Tunnel
Franklin	Metal Township	188.59	303.51	8 14	189	Willow Hill	PA 75 – Willow Hill, Fort Loudon
	Fannett–Lurgan township line	198.5– 199.4	319.5– 320.9	Kittatinny Mountain Tunnel
	Lurgan Township	199.5– 200.3	321.1– 322.4	Blue Mountain Tunnel
		201.29	323.94	9 15	201	Blue Mountain	PA 997 – Shippensburg, Chambersburg
Cumberland	Hopewell Township	202.50	325.89	Blue Mountain Service Plaza (westbound)
	West Pennsboro Township	219.10	352.61	Cumberland Valley Service Plaza (eastbound)
	Middlesex Township	226.54	364.58	11 16	226	Carlisle	US 11 to I-81 – Carlisle, Harrisburg, Chambersburg	I-81 exit 52; signed for Harrisburg eastbound, Chambersburg westbound; access to US Army War College and US Army Heritage Center; formerly called the Middlesex Interchange
	Upper Allen Township	236.22	380.16	17	236	Gettysburg Pike	US 15 – Gettysburg, Harrisburg	Access to Harrisburg State Capital
York	Fairview Township	241.87	389.25	18	242	Harrisburg West	I-83 – York, Baltimore, Harrisburg	I-83 exit 39B; access to Harrisburg State Capital
Susquehanna River		246.5– 247.3	396.7– 398.0	Susquehanna River Bridge
Dauphin	Lower Swatara Township	247.38	398.12	19	247	Harrisburg East	I-283 north to PA 283 east – Harrisburg, Hershey	Southern terminus of I-283; access to Harrisburg International Airport and Harrisburg State Capital
		249.70	401.85	Highspire Service Plaza (eastbound)
Dauphin–Lebanon county line	Conewago–South Londonderry township line	258.80	416.50	Lawn Service Plaza (westbound)
Lancaster	Rapho Township	266.45	428.81	20	266	Lebanon–Lancaster	PA 72 – Lebanon, Lancaster	Access to Cornwall Iron Furnace State Historic Site and Hershey
	East Cocalico Township	286.09	460.42	21	286	Reading	US 222 / PA 272 – Reading, Ephrata, Lancaster	Access via Colonel Howard Boulevard; PA 272 not signed; signed for Ephrata eastbound, Lancaster westbound; access to Ephrata Cloister and Landis Valley Museum
	Brecknock Township	289.90	466.55	Bowmansville Service Plaza (eastbound)
Berks	Caernarvon Township			22	–	Morgantown	PA 10 – Morgantown, Reading	Replaced by newer exit in 1996
		298.33	480.12	22	298	Morgantown	I-176 north to PA 10 / PA 23 – Morgantown, Reading	Southern terminus of I-176; access to Daniel Boone Homestead State Historical Site
Chester	Wallace Township	304.80	490.53	Peter J. Camiel Service Plaza (westbound)
	Uwchlan Township	311.93	502.00	23	312	Downingtown	PA 100 – Pottstown, West Chester	Access to Hopewell Furnace National Historic Site
	Charlestown–East Whiteland– Tredyffrin township tripoint	319.33	513.91	–	320	SR 29	PA 29 – Phoenixville, Malvern
	Tredyffrin Township	324.50	522.23	Valley Forge Service Plaza (eastbound)
Montgomery	Upper Merion Township	326.62	525.64	24	326	Valley Forge	I-76 east to I-476 / US 202 / US 422 west – Philadelphia, Valley Forge I-276 begins	I-76 exit 326; eastern end of I-76 overlap; western terminus of I-276; signed for I-476 eastbound, US 422 westbound; access to Valley Forge National Historical Park
		328.40	528.51	King of Prussia Service Plaza (westbound)
	Schuylkill River	331.7– 331.9	533.8– 534.1	Schuylkill River Bridge
	Plymouth Township	333.28	536.36	25	333	Norristown	I-476 south – Chester, Norristown	I-476 not signed westbound; access to Norristown via Plymouth Road
		334.5	538.3	–	–		I-476 north / Penna Turnpike NE Extension north – Allentown	Exits to northbound I-476 / Penna Turnpike NE Extension and entrances from southbound I-476 / Penna Turnpike NE Extension; southern terminus of Penna Turnpike NE Extension
				25A	20	Mid-County	I-476 south – Chester, Philadelphia	Westbound exit and eastbound entrance; exit no. corresponds to I-476; Philadelphia not signed westbound
	Upper Dublin Township	338.36	544.54	26	339	Fort Washington	PA 309 – Philadelphia, Ambler	Access to Hope Lodge State Historic Site
		339.80	546.86	26A	340	Virginia Drive	Virginia Drive	Westbound exit and entrance; no trucks
	Upper Moreland Township	342.91	551.86	27	343	Willow Grove	PA 611 – Doylestown, Jenkintown	Access to Graeme Park State Historic Site
Bucks	Bensalem Township	351.49	565.67	28	351	Bensalem	US 1 to I-95 south – Philadelphia, Trenton	I-95 not signed westbound; formerly called the Philadelphia Interchange;
		351.89	566.31	–	352	Street Road	PA 132 (Street Road)	Eastbound exit and entrance
		352.67	567.57	Neshaminy Falls Toll Gantry (eastern end of closed toll system)
	Bristol Township	41.1	66.1	–	40		I-95 south – Philadelphia I-276 ends	Westbound exit and eastbound entrance; I-95 exit 40; eastern terminus of I-276; western end of I-95 overlap
		42.4	68.2	29 358	42	Delaware Valley	US 13 – Levittown, Bristol
Delaware River		43.7	70.3	Delaware River–Turnpike Toll Bridge (westbound toll)
				–	–		I-95 north / Pearl Harbor Extension east to N.J. Turnpike – New Jersey, New York	Continuation into New Jersey; eastern end of I-95 overlap
1.000 mi = 1.609 km; 1.000 km = 0.621 mi       Concurrency terminus       Electronic toll collection       Closed/former       Incomplete access       Route transition       Unopened

See also

• List of toll roads in the United States

External links

Template:Attached KML/Pennsylvania Turnpike

KML is from Wikidata

• Official site
• Pennsylvania Highways: Pennsylvania Turnpike
• The Pennsylvania Turnpike @ Pennsylvania Road Photos
• Pennsylvania Roads - I-76 - Pennsylvania Turnpike
• Pennsylvania Roads - I-76 - Abandoned Tpk.
• Information About the Abandoned Sections of the Pennsylvania Turnpike
• Pennsylvania Roads - I-276 - Pennsylvania Turnpike
• The Pennsylvania Turnpike A History Archived June 8, 2009, at the Wayback Machine
• Pennsylvania @ AARoads - Interstate 76
• Pennsylvania @ AARoads - Interstate 276 / Pennsylvania Turnpike
• Pennsylvania @ AARoads - Interstate 95
• Interstate Guide – I-276
• I-276 on Kurumi.com
• The Roads of Metro Philadelphia: Pennsylvania Turnpike - Delaware River Extension (I-276)