Wikipedia

Formula One engines

(Redirected from Formula one engines)

This article gives an outline of Formula One engines, also called Formula One power units since the hybrid era starting in 2014. Since its inception in 1947, Formula One has used a variety of engine regulations. Formulae limiting engine capacity had been used in Grand Prix racing on a regular basis since after World War I. The engine formulae are divided according to era.[1][2][3]

Characteristics

edit

Formula One currently uses 1.6 litre four-stroke turbocharged 90 degree V6 double-overhead camshaft (DOHC) reciprocating engines.[4] They were introduced in 2014 and have been developed over the subsequent seasons. Mostly from the 2023 season, specifications on Formula One engines, including the software used to control them and the maximum per-engine price to F1 teams of € 15,000,000, have been frozen until the end of 2025, when the completely new 2026 spec will come into effect.

High revolutions

edit

The history of F1 engines has always been a quest for more power, and the enormous power a Formula One engine produces had been generated by operating at a very high rotational speed, reaching over 20,000 revolutions per minute (rpm) during the 2004-2005 seasons. This is because an engine, theoretically, produces double the power when operated twice as fast if combustion (thermal) efficiency and energy loss remain the same. High-revving engines won races no matter how much fuel it consumed and how much wasted heat it generated, as long as they produced more power over the competition. However, with the skyrocketing cost of exotic materials and production methods enabling the high-speed operation, and the realisation that such advancements in technology would likely never applied to production vehicles (because the resultant product is very inefficient), it was decided to limit the maximum rotational speed (rev) to 19,000 rpm in 2007. The maximum rev was further limited to 18,000 rpm in 2009, and to 15,000 rpm for the 2014-2021 seasons.[5]

Still, the high speed operation of F1 engines contrasts with road car engines of a similar size, which typically operate at less than 6,000 rpm.

Valve springs

edit

Until the mid-1980s Formula One engines were limited to around 12,000 rpm due to the traditional metal springs used to close the valves. The speed required to close the valves at a higher rpm called for ever stiffer springs, which increased the power required to drive the camshaft to open the valves, to the point where the loss nearly offset the power gain through the increase in rpm. They were replaced by pneumatic valve springs introduced by Renault in 1986,[6][7] which inherently have a rising rate (progressive rate) that allowed them to have an extremely high spring rate at larger valve strokes without much increasing the driving power requirements at smaller strokes, thus lowering the overall power loss. Since the 1990s, all Formula One engine manufacturers have used pneumatic valve springs with pressurised air.[7][8][9][10][11]

Piston speed

edit

In addition to the use of pneumatic valve springs, a Formula One engine's high rpm output has been made possible due to advances in metallurgy and design, allowing lighter pistons and connecting rods to withstand the accelerations necessary to attain such high speeds. Improved design also allows narrower connecting rod ends and so narrower main bearings. This permits higher rpm with less bearing-damaging heat build-up. For each stroke, the piston goes from a virtual stop to almost twice the mean speed (approximately 40 m/s), then back to zero. This occurs once for each of the four strokes in the cycle: one Intake (down), one Compression (up), one Power (ignition-down), one Exhaust (up). Maximum piston acceleration occurs at top dead center (TDC) and is in the region of 95,000 m/s2, about 9,700 times standard gravity (9,700 G).[a]

To lower the maximum piston/conrod acceleration, Formula One cars use short-stroke, multi-cylinder engines that result in lower average piston speed for a given displacement.[12] After seeing some 16 cylinder engines,[b] the number of cylinders was limited to twelve in 1989, ten in 2000, eight in 2006 and six in 2014. These regulation changes made higher-speed designs more difficult and less efficient. To operate at high engine speeds under such limits, the stroke must be short to prevent catastrophic failure, usually from the connecting rod, which is under very large stresses. Having a short stroke means a relatively large bore is required to reach a given displacement. This results in less efficient combustion, due mostly to flame-front propagation having to travel the long distance (for a volume) of ever thinner disk (larger diameter with less height) -shaped combustion chamber deviating far away from the ideal sphere shape with the tip of spark plug at its center.[13][14]

 Notes:

  1. ^ 95,000 / 9.807(standard gravity) = 9,686 This means if the reciprocating mass is 100 gram, a conrod must withstand 968.6 kg of pulling force at each TDC at the end of Exhaust stroke. The same force at the end of Compression stroke is counteracted by the combustion pressure, and the pushing (compression, as opposed to pulling) force at BDCs is smaller due to secondary imbalance inherent in piston engines. The current 1.6L V6 engines have 300 gram minimum weight restriction on each piston (with piston pin, pin retainers, and piston rings) and each conrod (with big-end bolts and shell metal bearings on each end). Although no 6 cylinder F1 engine has likely ever run at 20,000rpm, 600 g(gram) reciprocating mass at 9,000 G would result in over 5 tons of force generated 4,000 times each second (20,000 x 2 x 6 / 60 = 4,000 Each occurrence about 0.1 millisecond or less in duration). These pulling and pushing forces "need to be" generated by the engine at the expense of lower net power.(WP:CALC)
  2. ^ BRM Type 15, Coventry Climax FWMW and BRM P75

Efficiency

edit

Due to the higher speed operation and the tighter restriction on the number of cylinders, efficiency of a naturally aspirated Formula One engine did not improve much since the 1967 Ford Cosworth DFV and the mean effective pressure stayed at around 14 bar (1.4 MPa) for a long time.[15]

From the 2014 season, a new concept of limiting the maximum fuel flow rate was introduced, which limits the power if energy loss and air/fuel ratio are constant. While the bore and stroke figures are now fixed by the rules, this regulation promoted the competition to improve powertrain efficiency. As energy loss increases nearly exponentially with engine speed, the rev limit became meaningless, so it was lifted in 2022. Currently, F1 engines rev up to about 13,000rpm, while the combustion efficiency has risen to about 40 bar BMEP and beyond, using lean and rapid burn techniques enabling λ<1 (average air/fuel ratio much leaner than 14.7:1 by mass)[14] and very high mechanical and effective compression ratios.[a]

In addition, energy recovery systems from exhaust pressure (MGU-Heat) and engine brake (MGU-Kinetic) are allowed to further improve efficiency. MGU-H[16][17] is an electric motor/generator on the common shaft between the exhaust turbine and intake compressor of the turbocharger, while MGU-K[18] is also an electric motor/generator driven by (or driving) crankshaft at a fixed ratio.

Together with improvements on these energy recovery systems, F1 engines increased power using the same amount of fuel in recent years. For example, Honda RA621H[19] engine of 2021 season generated over 100 kW (130 bhp) more maximum power over RA615H of the 2015 season at the same 100 kg/h fuel flow rate.[20]

With the hugely improved efficiency of the combustion, mechanicals/software and turbocharger, F1 engines are generating much less heat and noise compared to the levels in 2014,[b] and Stefano Domenicali said the 2026 regulation will impose intentionally louder exhaust sound to please the fans.[21]

 Notes:

  1. ^ Compression ratio is a primary determinant of internal-combustion engine efficiency. Current regulation limits mechanical compression ratio to 18:1, but effective compression ratio after turbocharging is not limited. Honda has stated the 18:1 ratio was a target far beyond the imagination in 2014, but is "now starting to feel like a real limitation." Intake runner-length tuning contributes to raising the effective compression ratio on production vehicles, but Honda says their F1 engines are using the same resonance effect instead to lower the peaks in intake manifold pressure, leaving the work to raise the pressure to the turbocharger. They say this improves anti-knocking properties, enabling a higher boost.[14]
  2. ^ If a turbocharger converts 100% of the energy in engine exhaust into motive power, the exhaust from turbocharger will be at the ambient pressure and temperature, and dead silent. On the same token, if an engine converts 100% of the energy in fuel into power, it must operate silently at the ambient temperature.

History

edit

Formula One engines have come through a variety of regulations, manufacturers and configurations through the years.[22] It is imperative to understand the distinction among the terms "Grand Prix", "World Championship" and "Formula One" to come to grips with the history.

Car racing in various forms began almost immediately after the invention of the automobile, and many of the first organised car racing events were held in Europe before 1900. There had been the tradition of calling a particular race in an event with the name of the award given to the winner in France and some other countries, as traditional racing events often had multiple races and classes, like Men, Women, 100m, 1500m, breast-stroke, etc. In the case of the car race held in Pau, France in 1900, there were no class divisions, and no prize on record was given to the winner, René de Knyff driving a Panhard et Revassor (2.1L, 4 cylinder engine called the 'Phoenix'[23] jointly developed with Gottlieb Daimler in Germany, about 20 hp), who became the commissioner of the CSI later. In 1901, the event was named "Semaine de Pau (Week in Pau)" held at Circuit du Sud-Ouest, and the prizes awarded to the winners were "Grand Prix de Pau (Grand Prize of Pau)" for the "650 kg or heavier" class, "Grand Prix du Palais d'Hiver (Grand Prize of the Winter Palace)" for "400 - 650 kg" class, and "Second Grand Prix du Palais d'Hiver" for the "under 400 kg" class. This event is significant not only because it called the prizes Grand Prix, but also because it was one of the very first automobile race events, including the fastest class of cars, held on a closed circuit (the 1900 race was on an open road).

 
1.5 litre V12 supercharged engine from the Ferrari 125 of 1950
 
This Alfa Romeo 159 1.5L supercharged straight-8 engine of 1951 could produce up to 425 bhp (317 kW).

During and after World War I (1914 - 1918), it became obvious that the size of engines (and if they were supercharged), not the size and weight of cars, primarily determined how fast they could run. Also, wealthy people started enjoying racing the smaller and more evenly-matched Voiturette cars more than the no-limits "Voiture" 5-11L (mostly 4-cylinder) behemoths that contested the fastest class. In 1926, then-current Voiturette regulation of "up to 1,500 cc, supercharged" was adopted to the formerly-unlimited Voiture class of Grand Prix races in France, and Voiturette class was re-defined as "up to 1,100 cc, no supercharger".

Formula One was born as the first internationally unified regulation to define a class of racing cars in 1946 to be effective 1947. It was defined by Commission Sportive Internationale (CSI), the sporting branch of Fédération Internationale de l'Automobile (FIA), reflecting the Voiture regulation of "up to 1,500 cc supercharged, or 4,500 cc without supercharger". After Formula One was more or less 'ratified' or accepted by other countries, Formula Two was defined in 1947 as "up to 500 cc supercharged, or 2,000 cc without".[24]

In contrast to the pre-existed European Drivers' Championship,[note 1] Formula One events were meant to be competition among the countries. Each car, or team, represented a country in this 'international' race, with the cars painted in the "national colours", like red for Italy, green for the UK, silver for Germany, and blue for France. The World Championship for Drivers was defined by the CSI in 1949 for 1950 and onwards to honour the drivers, instead of the countries they represented.[25] The World Championship for Constructors started in 1958,[26] created partly to resolve the then-common dispute between a winning driver and his team on the ownership of the Grand Prix trophy. These championships had a longer-term effect of downplaying the country representation.

Over the years, Formula One added more and more regulations, not only on engines but chassis, tyres, fuel, inspections, championship points, penalties, safety measures, cost control, licensing, distribution of profits, how the qualifying and races must be governed and run, etc., etc. Today, the vast regulations on Power Unit are a very small part of what defines Formula One, which regulates even the number of Summer vacation days the constructor factories must observe.

1947–1953

edit

This era used pre-war voiturette engine regulations, with 4.5 L atmospheric and 1.5 L supercharged engines. The Indianapolis 500 (which was a round of the World Drivers' Championship from 1950 onwards) used pre-war Grand Prix regulations, with 4.5 L atmospheric and 3.0 L supercharged engines. The power range was up to 425 hp (317 kW), though the BRM Type 15 of 1953 reportedly achieved 600 hp (447 kW) with a 1.5 L supercharged engine.

In 1952 and 1953, the World Drivers' Championship was run to Formula Two regulations, but the existing Formula One regulations remained in force and a number of Formula One races were still held in those years.

 
A 2.5 L V8 in a Lancia-Ferrari D50 (1955–1956)

1954–1960

edit

Naturally-aspirated engine size was reduced to 2.5 L and supercharged cars were limited to 750 cc. No constructor built a supercharged engine for the World Championship. The Indianapolis 500 continued to use old pre-war regulations. The power range was up to 290 hp (216 kW).

1961–1965

edit
 
Porsche 804 had a fan to cool the air-cooled flat-8 engine

Introduced in 1961 amidst some criticism, the new reduced engine 1.5 L formula took control of F1 just as every team and manufacturer switched from front to mid-engined cars. Although these were initially underpowered, by 1965 average power had increased by nearly 50% and lap times were faster than in 1960. The old 2.5 L formula had been retained for International Formula racing, but this did not achieve much success until the introduction of the Tasman Series in Australia and New Zealand during the winter season, leaving the 1.5 L cars as the fastest single seaters in Europe during this time. The power range was between 150 hp (112 kW) and 225 hp (168 kW).

 
A 1968 British Racing Motors H16, 64-valve, Formula One engine

1966–1986

edit
 
A Cosworth DFV 3-litre V8 Formula One engine
 
Renault 1.5 litre turbo engine

In 1966, with sports cars capable of outrunning Formula One cars thanks to much larger and more powerful engines, the FIA increased engine capacity to 3.0 L atmospheric and 1.5 L compressed engines.[27] Although a few manufacturers had been aiming for larger engines, the transition was not smooth and 1966 was a transitional year, with 2.0 L versions of the BRM and Coventry-Climax V8 engines being used by several entrants. The appearance of the standard-produced Cosworth DFV in 1967 made it possible for small manufacturers to join the series with a chassis designed in-house. Compression devices were allowed for the first time since 1960, but it was not until 1977 that a company actually had the finance and interest of building one, when Renault debuted their new Gordini V6 turbocharged engine at that year's British Grand Prix at Silverstone. This engine had a considerable power advantage over the naturally-aspirated Cosworth DFV, Ferrari and Alfa Romeo engines.

By the start of the 1980s, Renault had proved that turbocharging was the way to go in order to stay competitive in Formula One, particularly at high-altitude circuits like Kyalami in South Africa and Interlagos in Brazil. Ferrari introduced their all-new V6 turbocharged engine in 1981, before Brabham owner Bernie Ecclestone managed to persuade BMW to manufacture straight-4 turbos for his team from 1982 onwards. In 1983, Alfa Romeo introduced a V8 turbo, and by the end of that year Honda and Porsche had introduced their own V6 turbos (the latter badged as TAG in deference to the company that provided the funding). Cosworth and the Italian Motori Moderni concern also manufactured V6 turbos during the 1980s, while Hart Racing Engines manufactured their own straight-4 turbo.

By mid-1985, every Formula One car was running with a turbocharged engine. In 1986, power figures were reaching unprecedented levels, with all engines reaching over 1,000 hp (750 kW) during qualifying with unrestricted turbo boost pressures. This was especially seen with the BMW straight-4 turbo, the M12/13, which produced around 1,400–1,500 hp (1,040–1,120 kW) at 5.5 bar of boost in qualifying trim, but was detuned to produce between 850–900 hp (630–670 kW) in race spec. However, these engines and gearboxes were very unreliable because of the engine's immense power, and would only last about four laps. For the race, the turbocharger's boost was restricted to ensure engine reliability; but the engines still produced 850–1,000 hp (630–750 kW) during the race.

The power range from 1966 to 1986 was between 285 hp (210 kW) to 500 hp (370 kW), turbos 500 hp (370 kW) to 900 hp (670 kW) in race trim, and in qualifying, up to 1,400 hp (1,040 kW). Following their experiences at Indianapolis, in 1971 Lotus made a few unsuccessful experiments with a Pratt & Whitney turbine fitted to chassis which also had four-wheel-drive.[28]

1987–1988

edit

Following the turbo domination, forced induction was allowed for two seasons before its eventual ban. The FIA regulations limited boost pressure, to 4 bar in qualifying in 1987 for 1.5 L turbo; and allowed a larger 3.5 L formula. Fuel tank sizes were further reduced in size to 150 litres for turbo cars to limit the amount of boost used in a race. These seasons were still dominated by turbocharged engines, the Honda RA167E V6 supplying Nelson Piquet winning the 1987 Formula One season on a Williams also winning the constructors championship, followed by TAG-Porsche P01 V6 in McLaren then Honda again with the previous RA166E for Lotus then Ferrari's own 033D V6.

 
A 1988 Honda RA168E turbocharged V6 engine

The rest of the grid was powered by the Ford GBA V6 turbo in Benetton, with the only naturally-aspirated engine, the DFV-derived Ford-Cosworth DFZ 3.5 L V8 outputting 575 hp (429 kW) in Tyrrell, Lola, AGS, March and Coloni.[29] The massively powerful BMW M12/13 inline-four found in the Brabham BT55 tilted almost horizontally, and in upright position under the Megatron brand in Arrows and Ligier, producing 900 bhp (670 kW) at 3.8 bar in race trim, and an incredible 1,400–1,500 bhp (1,040–1,120 kW) at 5.5 bar of boost in qualifying spec.[30] Zakspeed was building its own turbo inline-four, Alfa Romeo was to power the Ligiers with an inline-four but the deal fell through after initial testing had been carried out. Alfa was still represented by its old 890T V8 used by Osella, and Minardi was powered by a Motori Moderni V6.

In 1988, six teams – McLaren, Ferrari, Lotus, Arrows, Osella and Zakspeed – continued with turbocharged engines, now limited to 2.5 bar. Honda's V6 turbo, the RA168E, which produced 685 hp (511 kW) at 12,300 rpm in qualifying,[31] powered the McLaren MP4/4 with which Ayrton Senna and Alain Prost won fifteen of the sixteen races between them. The Italian Grand Prix was won by Gerhard Berger in the Ferrari F1/87/88C, powered by the team's own V6 turbo, the 033E, with about 720 hp (537 kW) at 12,000 rpm in qualifying and 620 hp (462 kW) at 12,000 rpm in races.[32] The Honda turbo also powered Lotus's 100T, while Arrows continued with the Megatron-badged BMW turbo, Osella continued with the Alfa Romeo V8 (now badged as an Osella) and Zakspeed continued with their own straight-4 turbo. All the other teams used naturally aspirated 3.5 L V8 engines: Benetton used the Cosworth DFR, which produced 585 hp (436 kW) at 11,000 rpm;[33] Williams, March and Ligier used the Judd CV, producing 600 hp (447 kW);[34] and the rest of the grid used the previous year's 575 hp (429 kW) Cosworth DFZ.

1989–1994

edit
 
A 1990 Renault RS2 V10 engine

Turbochargers were banned from the 1989 Formula One season, leaving only a naturally aspirated 3.5 L formula. Honda was still dominant with their RA109E 72° V10 giving 685 hp (511 kW) @ 13,500 rpm on McLaren cars, enabling Prost to win the championship in front of his teammate Senna. Behind were the Renault RS1-powered Williams, a 67° V10 giving 650 hp (485 kW) @ 12,500 rpm and the Ferrari with its 035/5 65° V12 giving 660 hp (492 kW) at 13,000 rpm. Behind, the grid was powered mainly by Ford Cosworth DFR V8 giving 620 hp (462 kW) @ 10,750 rpm except for a few Judd CV V8 in Lotus, Brabham and EuroBrun cars, and two oddballs: the 620 hp (460 kW) Lamborghini 3512 80° V12 powering Lola, and the 560 hp (420 kW) Yamaha OX88 75° V8 in Zakspeed cars. Ford started to try its new design, the 75° V8 HBA1 with Benetton.

 
A 1990 W12 3.5 Formula One engine from the Life F1 car

The 1990 Formula One season was again dominated by Honda in McLarens with the 690 hp (515 kW) @ 13,500 rpm RA100E powering Ayrton Senna and Gerhard Berger ahead of the 680 hp (507 kW) @ 12,750 rpm Ferrari Tipo 036 of Alain Prost and Nigel Mansell. Behind them the Ford HBA4 for Benetton and Renault RS2 for Williams with 660 hp (492 kW) @ 12,800 rpm were leading the pack powered by Ford DFR and Judd CV engines. The exceptions were the Lamborghini 3512 in Lola and Lotus, and the new Judd EV 76° V8 giving 640 hp (477 kW) @ 12,500 rpm in Leyton House and Brabham cars. The two new contenders were the Life which built for themselves an F35 W12 with three four cylinders banks @ 60°, and Subaru giving Coloni a 1235 flat-12 from Motori Moderni

 
A 1991 Honda RA121E V12 engine

Honda was still leading the 1991 Formula One season in Senna's McLaren with the 725–780 hp (541–582 kW) @ 13,500–14,500 rpm 60° V12 RA121E, just ahead of the Renault RS3 powered Williams benefiting from 700–750 hp (520–560 kW) @ 12,500–13,000 rpm. Ferrari was behind with its Tipo 037, a new 65° V12 giving 710 hp (529 kW) @ 13,800 rpm also powering Minardi, just ahead the Ford HBA4/5/6 in Benetton and Jordan cars. Behind, Tyrrell was using the previous Honda RA109E, Judd introduced its new GV with Dallara leaving the previous EV to Lotus, Yamaha were giving its 660 hp (492 kW) OX99 70° V12 to Brabham, Lamborghini engines were used by Modena and Ligier. Ilmor introduced its LH10, a 680 hp (507 kW) @ 13,000 rpm V10 which eventually became the Mercedes with Leyton House and Porsche sourced a little successful 3512 V12 to Footwork Arrows; the rest of the field was Ford DFR powered.[35]

In 1992, the Renault engines became dominant, even more so following the departure from the sport of Honda at the end of 1992. The 3.5 L Renault V10 engines powering the Williams F1 team produced a power output between 750–820 bhp (559–611 kW; 760–831 PS) @ 13,000–14,300 rpm toward the end of the 3.5 L naturally-aspirated era, between 1992 and 1994. Renault-engined cars won the last three consecutive world constructors' championships of the 3.5 L formula era with Williams (1992–1994).[36]

The Peugeot A4 V10, used by the McLaren Formula One team in 1994, initially developed 700 bhp (522 kW; 710 PS) @ 14,250 rpm. It was later further developed into the A6, which produced even more power, developing 760 bhp (567 kW; 771 PS) @ 14,500 rpm.

The EC Zetec-R V8, which powered the championship-winning Benetton team and Michael Schumacher in 1994, produced between 730–750 bhp (544–559 kW; 740–760 PS) @ 14,500 rpm.[37]

 
1994 Ferrari Tipo 043 3.5 V12 engine; the most powerful 3.5-litre engine in F1 history

By the end of the 1994 season, Ferrari's Tipo 043 V12 was putting out around 850 hp (634 kW)[38] @ 15,800 rpm, which is to date the most-powerful naturally-aspirated V12 engine ever used in Formula One. This was also the most powerful engine of 3.5-litre engine regulation era, before a reduction in engine capacity to 3 litres in 1995.[39]

1995–2005

edit
 
Ferrari Tipo 044/1 3.0-litre V12 F1 engine (1995)
 
A 2004 Ferrari model 053 V10 engine of the Ferrari F2004

This era used a 3.0 L formula, with the power range varying (depending on engine tuning) between 600 hp (447 kW) and 1,000 hp (746 kW), between 13,000 rpm and 20,000 rpm, and from eight to twelve cylinders. Despite engine displacement being reduced from 3.5 L, power figures and RPMs still managed to climb. Renault was the initial dominant engine supplier from 1995 until 1997, winning the first three world championships with Williams and Benetton in this era. The championship-winning 1995 Benetton B195 produced a power output of 675 hp (503.3 kW) @ 15,200 rpm, and the 1996 championship-winning Williams FW18 produced 700 hp (522.0 kW) @ 16,000 rpm; both from a shared Renault RS9 3.0 L V10 engine.[40][41] The 1997 championship-winning FW19 produced between 730–760 hp (544.4–566.7 kW) @ 16,000 rpm, from its Renault RS9B 3.0 L V10. Ferrari's last V12 engine, the Tipo 044/1, was used in 1995. The engine's design was largely influenced by major regulation changes imposed by the FIA after the dreadful events during the year before: the V12 engine was reduced from 3.5 to 3.0 litres. The 3.0-litre engine produced around 700 hp (522 kW) 17,000 rpm in race trim; but was reportedly capable of producing up to 760 hp (567 kW) in its highest state of tune for qualification mode.[42] Between 1995 and 2000, cars using this 3.0 L engine formula, imposed by the FIA, produced a constant power range (depending on engine type and tuning), varying between 600 hp and 815 hp. Most Formula One cars during the 1997 season comfortably produced a consistent power output of between 665–760 hp (495.9–566.7 kW), depending on whether a V8 or V10 engine configuration was used.[43] From 1998 to 2000 it was Mercedes' power that ruled, giving Mika Häkkinen two world championships. The 1999 McLaren MP4/14 produced between 785 and 810 hp @ 17,000 rpm. Ferrari gradually improved their engine. In 1996, they changed from their traditional V12 engine to a smaller and lighter V10 engine. They preferred reliability to power, losing out to Mercedes in terms of outright power initially. Ferrari's first V10 engine, in 1996, produced 715 hp (533 kW) @ 15,550 rpm,[44] down on power from their most powerful 3.5 L V12 (in 1994), which produced over 830 hp (619 kW) @ 15,800 rpm, but up on power from their last 3.0 L V12 (in 1995), which produced 700 hp (522 kW) @ 17,000 rpm. At the 1998 Japanese GP, Ferrari's 047D engine spec was said to produce over 800 bhp (600 kW), and from 2000 onward, they were never short of power or reliability. To keep costs down, the 3.0 L V10 engine configuration was made fully mandatory for all teams in 2000 so that engine builders would not develop and experiment with other configurations.[45] The V10 configuration had been the most popular since the banning of turbocharged engines in 1989, and no other configuration had been used since 1998.

BMW started supplying its engines to Williams from 2000. The engine was very reliable in the first season though slightly short of power compared to Ferrari and Mercedes units. The BMW E41-powered Williams FW22 produced around 810 hp @ 17,500 rpm, during the 2000 season.[46] BMW went straight forward with its engine development. The P81, used during the 2001 season, was able to hit 17,810 rpm. Unfortunately, reliability was a large issue with several blowups during the season.

The BMW P82, the engine used by the BMW WilliamsF1 Team in 2002, had hit a peak speed of 19,050 rpm in its final evolutionary stage. It was also the first engine in the 3.0 litre V10-era to break through the 19,000 rpm wall, during the 2002 Italian Grand Prix's qualifying.[47] BMW's P83 engine used in 2003 season managed an impressive 19,200 rpm and cleared the 900 bhp (670 kW) mark, at around 940 bhp, and weighs less than 200 lb (91 kg).[48][49] Honda's RA003E V10 also cleared the 900 bhp (670 kW) mark at the 2003 Canadian Grand Prix.[50]

In 2005, the 3.0 L V10 engine permitted no more than 5 valves per cylinder.[51] Also, the FIA introduced new regulations limiting each car to one engine per two Grand Prix weekends, putting the emphasis on increased reliability. In spite of this, power outputs continued to rise. Mercedes engines had about 930 bhp (690 kW) in this season. Cosworth, Mercedes, Renault, and Ferrari engines all produced around 900 bhp (670 kW) to 940 bhp (700 kW) @ 19,000 rpm.[52] Honda had over 965 bhp (720 kW).[53][54] The BMW engine made over 950 bhp (710 kW).[55][56] Toyota engines had over 1,000 bhp (750 kW), according to Toyota Motorsport's executive Vice President, Yoshiaki Kinoshita.[57] However, for reliability and longevity purposes, this power figure may have been detuned to around 960 bhp (720 kW) for races.[58]

2006–2013

edit
 
Renault RS26 2.4 V8 engine (2006)

For 2006, the engines had to be 90° V8 of 2.4 litres maximum capacity with a circular bore of 98 mm (3.9 in) maximum, which implies a 39.75 mm (1.565 in) stroke at maximum bore. The engines must have two inlet and two exhaust valves per cylinder, be naturally aspirated and have a 95 kg (209 lb) minimum weight. The previous year's engines with a rev-limiter were permitted for 2006 and 2007 for teams who were unable to acquire a V8 engine, with Scuderia Toro Rosso using a Cosworth V10, after Red Bull's takeover of the former Minardi team did not include the new engines.[59] The 2006 season saw the highest rev limits in the history of Formula One, at well over 20,000 rpm; before a 19,000 rpm mandatory rev limiter was implemented for all competitors in 2007. Cosworth was able to achieve just over 20,000 rpm with their V8,[60] and Renault around 20,500 rpm. Honda did the same; albeit only on the dynamometer.

Pre-cooling air before it enters the cylinders, injection of any substance other than air and fuel into the cylinders, variable-geometry intake and exhaust systems, and variable valve timing were forbidden. Each cylinder could have only one fuel injector and a single plug spark ignition. Separate starting devices were used to start engines in the pits and on the grid. The crankcase and cylinder block had to be made of cast or wrought aluminium alloys. The crankshaft and camshafts had to be made from an iron alloy, pistons from an aluminium alloy, and valves from alloys based on iron, nickel, cobalt or titanium. These restrictions were in place to reduce development costs on the engines.[61]

 
Ferrari Tipo 056 2.4 L V8 engine

The reduction in capacity was designed to give a power reduction of around 20% from the three-litre engines, to reduce the increasing speeds of Formula One cars. Despite this, in many cases the performance of the car improved. In 2006 Toyota F1 announced an approximate 740 hp (552 kW) output at 18,000 rpm for its new RVX-06 engine,[62] but real figures are of course difficult to obtain. Most cars from this period (2006–2008) produced a regular power output of approximately between 720 and 800 hp @ 19,000 rpm (over 20,000 rpm for the 2006 season).[63]

The engine specification was frozen in 2007 to keep development costs down. The engines which were used in the 2006 Japanese Grand Prix were used for the 2007 and 2008 seasons and they were limited to 19,000 rpm. In 2009 the limit was reduced to 18,000 rpm with each driver allowed to use a maximum of 8 engines over the season. Any driver needing an additional engine is penalised 10 places on the starting grid for the first race the engine is used. This increases the importance of reliability, although the effect is only seen towards the end of the season. Certain design changes intended to improve engine reliability may be carried out with permission from the FIA. This has led to some engine manufacturers, notably Ferrari and Mercedes, exploiting this ability by making design changes which not only improve reliability but also boost engine power output as a side effect. As the Mercedes engine was proven to be the strongest, re-equalisations of engines were allowed by the FIA to allow other manufacturers to match the power.[64]

2009 saw the exit of Honda from Formula One. The team was acquired by Ross Brawn, creating Brawn GP and the BGP 001. With the absence of the Honda engine, Brawn GP retrofitted the Mercedes engine to the BGP 001 chassis. The newly branded team won both the Constructors' Championship and the Drivers' Championship from better-known and better-established contenders Ferrari, McLaren-Mercedes, and Renault.

Cosworth, absent since the 2006 season, returned in 2010. New teams Lotus Racing, HRT, and Virgin Racing, along with the established Williams, used this engine. The season also saw the withdrawal of the BMW and Toyota engines, as the car companies withdrew from Formula One due to the Great Recession.[65]

In 2009, constructors were allowed to use kinetic energy recovery systems (KERS), also called regenerative brakes. Energy can either be stored as mechanical energy (as in a flywheel) or as electrical energy (as in a battery or supercapacitor), with a maximum power of 81 hp (60 kW; 82 PS) deployed by an electric motor, for a little over 6 seconds per lap. Four teams used it at some point in the season: Ferrari, Renault, BMW, and McLaren.[66]

Although KERS was still legal in F1 in the 2010 season, all the teams agreed not to use it. KERS returned for the 2011 season, when only three teams elected not to use it. For the 2012 season, only Marussia and HRT raced without KERS, and in 2013 all teams on the grid had KERS. From 2010 to 2013 cars have a regular power of 700–800 hp, averaging around 750 hp @ 18,000 rpm.[67][68]

2014–2021

edit

The FIA announced a change from the 2.4-litre V8, introducing 1.6-litre V6 hybrid engines (more than one power source) for the 2014 season. The new regulations allow kinetic and heat energy recovery systems.[69] Forced induction was now allowed – either turbochargers, which last appeared in 1988, or superchargers – with all constructors opting to use a turbocharger. Instead of limiting the boost level, the regulations introduced a fuel flow restriction at 100 kg of petrol per hour maximum. The engines sounded very different from the previous formula, due to the lower rev limit (15,000 rpm) and the turbocharger.

The new formula for turbocharged engines have their efficiency improved through turbo-compounding by recovering energy from exhaust gases.[70] The original proposal for four-cylinder turbocharged engines was not welcomed by the racing teams, in particular Ferrari. Adrian Newey stated during the 2011 European Grand Prix that the change to a V6 enables teams to carry the engine as a stressed member, whereas an inline-4 would have required a space frame. A compromise was reached, allowing V6 forced induction engines instead.[70] The engines rarely exceed 12,000 rpm during qualifying and race, due to the new fuel flow restrictions.[71]

Energy recovery systems such as KERS had a boost of 160 hp (120 kW) and 2 megajoules per lap. KERS was renamed Motor Generator Unit–Kinetic (MGU-K). Heat energy recovery systems were also allowed, under the name Motor Generator Unit–Heat (MGU-H)

The 2015 season was an improvement on 2014, adding about 30–50 hp (20–40 kW) to most engines, the Mercedes engine being the most powerful with 870 hp (649 kW). In 2019, Renault's engine was claimed to have hit 1,000 hp in qualifying trim.[72]

Of the previous manufacturers, only Mercedes, Ferrari and Renault produced engines to the new formula in 2014, whereas Cosworth stopped supplying engines. Honda returned as an engine manufacturer in 2015, with McLaren switching to Honda power after using the Mercedes engine in 2014. In 2019, Red Bull switched from using a Renault engine to Honda power. Honda supplied both Red Bull and AlphaTauri. Honda withdrew as a power unit supplier at the end of 2021, with Red Bull taking over the project and producing the engine in-house.[73]

2022–2025

edit

In 2017, the FIA began negotiations with existing constructors and potential new manufacturers over the next generation of engines with a projected introduction date of 2021 but delayed to 2022 due to the effects of the COVID-19 pandemic.[74] The initial proposal was designed to simplify engine designs, cut costs, promote new entries and address criticisms directed at the 2014 generation of engines. It called for the 1.6 L V6 configuration to be retained, but abandoned the complex Motor Generator Unit–Heat (MGU-H) system.[75] The Motor Generator Unit–Kinetic (MGU-K) would be more powerful, with a greater emphasis on driver deployment and a more flexible introduction to allow for tactical use. The proposal also called for the introduction of standardised components and design parameters to make components produced by all manufacturers compatible with one another in a system dubbed "plug in and play".[75] A further proposal to allow four-wheel drive cars was also made, with the front axle driven by an MGU-K unit—as opposed to the traditional driveshaft—that functioned independently of the MGU-K providing power to the rear axle, mirroring the system developed by Porsche for the 919 Hybrid race car.[76][77]

However, mostly due to no new engine supplier applying for F1 entry in 2021 and 2022, abolishment of the MGU-H, a more powerful MGU-K and a four-wheel drive system were all shelved with the possibility of their re-introduction for 2026. Instead, the teams and FIA agreed to a radical change in body/chassis aerodynamics to promote more battles on the course at closer distances to each other. They further agreed to an increase in alcohol content from 5.75% to 10% of fuel, and to implement a freeze on power unit design for 2022-2025, with the internal combustion engine (ICE), turbocharger and MGU-H being frozen on March 1 and the energy store, MGU-K and control electronics being frozen on September 1 during the 2022 season.[78] Honda, the outgoing engine supplier in 2021, was keen to keep the MGU-H, and Red Bull, who took over the engine production project, backed that opinion.[79] The 4WD system was planned to be based on Porsche 919 Hybrid system,[76] but Porsche ended up not becoming an F1 engine supplier for 2021-2022.

2026 onwards

edit

New engine regulations will be introduced from the 2026 season. These engine regulations will see the turbocharged 1.6 V6 internal combustion engine configuration used since 2014 retained. The new power units will produce over 1,000 bhp (750 kW), although the power will come from different places. The MGU-H (Motor Generator Unit – Heat) will be banned, while the MGU-K's (Motor Generator Unit – Kinetic) output will increase to 470 bhp (350 kW) – previously the MGU-H and MGU-K produced a combined power output of 160 bhp (120 kW). The power output of the internal combustion part of the power unit will decrease to 540 bhp (400 kW) from 850 bhp (630 kW). In addition, fuel flow rates will be measured and limited based on energy, rather than mass or volume of the fuel itself. There is also intended to be further restrictions on components such as MGU-Ks and exhausts imposed from 2027. The new power units are due to be run on a fully sustainable fuel, being developed by Formula One.[80][81]

Audi are due to become an engine provider from 2026 onwards.[82] Ford are due to partner with Red Bull Powertrains as Red Bull Ford Powertrains from 2026 after a 20 year absence.[83][84][85] Honda, under its subsidiary Honda Racing Corporation, has also entered as a manufacturer for 2026 by the FIA after officially leaving the sport in 2021.[86] The FIA also confirmed that Ferrari, Mercedes-AMG and Alpine (Renault) were registered as power unit suppliers for 2026.[87] However, on 30th September 2024, owing to lack of strong results with its' power unit during the V6 turbo-hybrid era since it began in 2014, Renault announced it would be ending its' engine programme following the conclusion of the 2025 championship and would not be making engines for the new 2026 regulations after all.[88]

Engine regulation progression by era

edit
Years Operating
principle[a] 		Maximum displacement Configuration RPM
limit 		Fuel flow
limit (Qmax) 		Fuel composition
Naturally
aspirated 		Forced
induction 		Alcohol Petrol
1947–1953[b] Unspecified 4.5 L 1.5 L Unrestricted Unrestricted[89] Unrestricted Unrestricted Unrestricted
1954–1957 2.5 L 0.75 L
1958–1960 Prohibited
1961–1962 1.5 L
(1.3 L min.) 		Prohibited
1963–1965 Pump Gasoline[90]
1966–1980 3.0 L 1.5 L Unrestricted
1981–1985 4-stroke piston
1986 Prohibited
1987 3.5 L 1.5 L, 4 bar
1988 1.5 L, 2.5 bar
1989–1991 Prohibited Up to 12
cylinders
1992–1994 Unleaded
1995–1999 3.0 L
2000–2005 V10
2006[c][91] 2.4 L 90° V8
2007[c] 19,000 rpm
2008 5.75%[d]
2009–2013[e] 90° V8 + KERS 18,000 rpm
2014–2021[f] 1.6 L[g][92][93] 90° V6 + MGUs 15,000 rpm[h] (0.009 x rpm)+5.5
up to 100 kg/h [i]
2022–2025[f][94] 1.6 L[j] Unrestricted[h] ≥10%[k]
2026 onwards 90° V6 + MGU (0.27 x rpm)+165 up to 3000 MJ/h [l] TBA[m]

 Notes:

  1. ^ 2-stroke, gas turbine, rotary, etc.
  2. ^ For 1952 and 1953, World Championship races were run to Formula Two rules (0.75 L with compressor, 2 L without), but Formula One regulations remained intact.
  3. ^ a b For 2006 and 2007, the FIA reserved the right to give special dispensations to teams without access to new specification engines to use 2005-spec engines with a rev-limiter. This dispensation was given to Scuderia Toro Rosso only in 2006.
  4. ^ 5.75% bio-sourced alcohol content is required.
  5. ^ Kinetic (braking) energy recovery system (KERS) allowed.
  6. ^ a b MGU (Motor Generator Unit)-Kinetic (brake) and MGU-Heat (exhaust) energy recovery systems allowed.
  7. ^ Smaller displacement is allowed. Naturally aspirated engines are not prohibited, but were not used by any team. Boost pressure is not limited, but fuel flow rate (which was not regulated up to 2013) is limited to 100 kg per hour (roughly equivalent to 3.5 bar at the maximum rpm).[citation needed]
  8. ^ a b Lower rpm fuel flow restriction on the next column reaches the maximum of 100kg/hour at 10,500rpm. At this flow rate, further increasing rpm requires lower boost, or results in thinner air/fuel ratio. Due to this, engine manufacturers normally set the maximum engine speed at about 13,000 rpm.
  9. ^ Maximum fuel flow rate (Q) is limited in relation to engine speed below 10,500rpm. On or above 10,500rpm, the maximum fuel flow rate of 100kg/hour applies.
  10. ^ Displacement must be between 1,590cc and 1,600cc. Naturally aspirated engines are not prohibited. Boost pressure is not limited.
  11. ^ 10% ethanol content is required.
  12. ^ Maximum fuel flow rate (Q) is limited in relation to engine speed below 10,500 rpm. On or above 10,500 rpm, the maximum fuel flow rate of 3000 MJ/h applies.
  13. ^ Formula One is developing a new sustainable fuel to be used from 2026, the composition of which has not been announced.

Current engine technical specifications

edit

Combustion, construction, operation, power and fuel

edit
  • Manufacturers: Mercedes-Benz, Renault (including TAG Heuer rebadging until 2018), Ferrari and Red Bull Powertrains (Honda)
  • Type: Hybrid-powered 4-stroke piston. '4-stroke' may imply Otto-cycle, but it is not required. Atkinson/Miller cycle allowed.
  • Configuration: V6 single hybrid turbocharger engine
  • V-angle: 90° cylinder angle
  • Displacement: 1.6 litres (98 cubic inches)
  • Bore: 80 mm (3.150 in)
  • Stroke: 53 mm (2.087 in)
  • Compression ratio: Max 18:1
  • Valvetrain: DOHC, 24-valve (four valves per cylinder)
  • Fuel: Minimum 87 (RON+MON)/2 unleaded petroleum + at least 10% "advanced sustainable" Ethanol[a]
  • Fuel delivery: Petrol direct injection
  • Maximum fuel injection pressure: 500 bar (50.0 MPa)
  • Number of fuel injectors: Max 1 per cylinder.[d]
  • Fuel flow rate limit: (0.009 x rpm) + 5.5 up to 100 kg/h [e]
  • Fuel use limit: 110 kg / race
  • Aspiration: Single-Turbocharger with in-line electric motor/generator (MGU-H)
  • Power output: About 850 + 161 hp (634 + 120 kW) @ 10,500 rpm and higher
  • Torque: Approx. 600–815 N⋅m (443–601 lb⋅ft)[96]
  • Lubrication: Dry sump[f]
  • Maximum revs: Unlimited (in practice, no engine goes much above 12,000 rpm as efficiency declines) [g]
  • Engine management: FIA Standard ECU [h]
  • Max. speed: Approximately 370 km/h (230 mph) (Monza, Baku and Mexico); 340 km/h (211 mph) normal tracks
  • Mass: Minimum 150 kg (330.69 lb) complete
  • Cooling: Single water pump
  • Ignition: No more than 5 sparks during Compression and Expansion (Power) cycles
  • Exhaust systems: Single exhaust with central exit and extra double small exhaust
Forced induction
edit
  • Turbocharger mass: 8 kg (17.6 lb) depending on the turbine housing used
  • Turbocharger rev limit: 125,000 rpm
  • Pressure charging: Single-stage compressor and exhaust turbine, common-shaft with MGU-H
  • Turbo boost pressure: Unlimited but typically 400–500 kPa (4.0–5.0 bar) absolute
  • Wastegate: Maximum of two pop-off and two wastegate valves[i], electronic- or pneumatic-controlled
ERS systems
edit
  • MGU-K RPM: Max 50,000 rpm, fixed driven/drive ratio by/to the crankshaft
  • MGU-K power: Max 120 kW (160 bhp)
  • Energy recovered by MGU-K: Max 2 MJ (0.56 kWh) / lap
  • Energy received by MGU-K: Max 4 MJ (1.1 kWh) / lap from Energy Store[j], unlimited from MGU-H[k]
  • MGU-H RPM: Same as the turbocharger speed. Max 125,000 rpm
  • Energy recovered by MGU-H: Unlimited[k]
  • Energy released by MGU-H to drive the turbocharger or MGU-K:[l] Unlimited[k]

 Notes:

  1. ^ There are finer composition and property limitations, but improvements within the limits are allowed, provided a sample is submitted and approved by FIA. Honda, for example, requested and Mobil agreed to provide, special formulations with carbon-neutral components suited for lean/rapid-burn techniques.[95]
  2. ^ 1,600 cc / 6 / (18 - 1) = 15.7 cc
  3. ^ A small chamber around the tip of spark plug within the 15.7 cc[b] minimum combustion chamber volume, with holes facing the main chamber.
  4. ^ This is a severe limitation on stratified charge and sub-chamber[c] ignition used for lean and rapid burn, as separate injectors cannot be used for sub- and main chambers to provide rich and lean gas.[14] The number of injections per cycle is not limited.
  5. ^ There are further limits under partial-throttle conditions.
  6. ^ Oil may not contain fuel octane boosting additives. Oil consumption is limited to Max 0.30L / 100 km. (Fluid level in oil tank is monitored by telemetry)
  7. ^ This is also a function of MGU-K drive ratio. If a team decides to drive MGU-K at 1:4 (one crank rotation to 4 MGU-K rotations overdrive. Ratio must be fixed), then the max engine rev becomes 50,000rpm(max speed of MGU-K) / 4 = 12,500rpm. This ratio is normally dictated by the engine supplier.
  8. ^ ECU (Electronic Control Unit) controls energy recovery and other chassis control / telemetry functions as well. Power unit control part of the ECU evolved from McLaren TAG-320B of 2019. Most parts of the program to operate the ECU were free to be improved as long as their copies (versions) submitted, registered and approved by FIA (there were limitations on the number of versions in a season), but Power Unit control part of the program is frozen from 2023 to 2025 seasons.
  9. ^ Pop-off valves limit the intake pressure by recirculating the charge. Wastegate valves release excess pressure to the atmosphere.
  10. ^ a b A combination of high voltage Lithium-ion battery with a series of Super Capacitors acting as the buffer for high charge/discharge currents. Max Voltage: 1000V, Weight limit: 20-25 kg.
  11. ^ a b c Due to these rules, the turbocharger is often used not to increase intake pressure (i.e. with pop-off valve open), but to drive MGU-H which provides electricity so that MGU-K output is pegged at 120kW for maximum acceleration regardless of the engine speed.
  12. ^ MGU-H generates electricity, which is used to charge the battery (Energy Store[j]) and/or to drive MGU-K; or, it consumes electricity to accelerate the turbocharger.

Records

edit

Figures correct as of the 2024 São Paulo Grand Prix

Bold indicates engine manufacturers that have competed in Formula One in the 2024 season.

World Championship Grand Prix wins by engine manufacturer

edit
Rank Engine Wins First win Latest win
1 Ferrari 249 1951 British Grand Prix 2024 Mexico City Grand Prix
2 Mercedes[a] 220 1954 French Grand Prix 2024 Singapore Grand Prix
3 Ford[b] 176 1967 Dutch Grand Prix 2003 Brazilian Grand Prix
4 Renault 169 1979 French Grand Prix 2021 Hungarian Grand Prix
5 Honda 89 1965 Mexican Grand Prix 2021 Abu Dhabi Grand Prix
6 Coventry Climax 40 1958 Argentine Grand Prix 1965 German Grand Prix
7 Honda RBPT[c] 29 2023 Bahrain Grand Prix 2024 São Paulo Grand Prix
8 TAG[d] 25 1984 Brazilian Grand Prix 1987 Portuguese Grand Prix
9 BMW 20 1982 Canadian Grand Prix 2008 Canadian Grand Prix
10 BRM 18 1959 Dutch Grand Prix 1972 Monaco Grand Prix
11 Red Bull Powertrains[c] 17 2022 Saudi Arabian Grand Prix 2022 Abu Dhabi Grand Prix
12 Alfa Romeo 12 1950 British Grand Prix 1978 Italian Grand Prix
13 Offenhauser 11 1950 Indianapolis 500[e] 1960 Indianapolis 500
Maserati 1953 Italian Grand Prix 1967 South African Grand Prix
15 Vanwall 9 1957 British Grand Prix 1958 Moroccan Grand Prix
TAG Heuer[f] 2016 Spanish Grand Prix 2018 Mexican Grand Prix
17 Repco 8 1966 French Grand Prix 1967 Canadian Grand Prix
18 Mugen-Honda 4 1996 Monaco Grand Prix 1999 Italian Grand Prix
19 Matra 3 1977 Swedish Grand Prix 1981 Canadian Grand Prix
20 Porsche 1 1962 French Grand Prix
Weslake 1967 Belgian Grand Prix
BWT Mercedes[g] 2020 Sakhir Grand Prix

Most wins in a season

edit

By number

edit
Rank Manufacturer Season Races Wins Percentage Engine(s) Winning team(s)
1 Honda RBPT 2023 22 21 95.5% Honda RBPTH001 Red Bull
2 Mercedes 2016 21 19 90.5% PU106C Hybrid Mercedes
3 Red Bull Powertrains 2022 22 17 77.3% RBPTH001 Red Bull
4 Renault 1995 17 16 94.1% RS7 Benetton, Williams
Mercedes 2014 19 84.2% PU106A Hybrid Mercedes
2015 19 84.2% PU106B Hybrid Mercedes
7 Ford 1973 15 15 100% DFV Lotus, Tyrrell, McLaren
Honda 1988 16 93.8% RA168E McLaren
Ferrari 2002 17 88.2% Tipo 050, Tipo 051 Ferrari
2004 18 83.3% Tipo 053 Ferrari
Mercedes 2019 21 71.4% M10 EQ Power+ Mercedes

By percentage

edit
Rank Manufacturer Season Races Wins Percentage Engine(s) Winning team(s)
1 Ford 1969 11 11 100% DFV Matra, Brabham, Lotus, McLaren
1973 15 15 DFV Lotus, Tyrrell, McLaren
3 Honda RBPT 2023 22 21 95.5% RBPTH001 Red Bull Racing
4 Renault 1995 17 16 94.1% RS7 Benetton, Williams
5 Honda 1988 16 15 93.8% RA168E McLaren
6 Ford 1968 12 11 91.7% DFV Lotus, McLaren, Matra
7 Mercedes 2016 21 19 90.5% PU106C Hybrid Mercedes
8 Ferrari 2002 17 15 88.2% Tipo 050, Tipo 051 Ferrari
9 Ferrari[h] 1952 8 7 87.5% Tipo 500, Tipo 375 Ferrari
10 Alfa Romeo[h] 1950 7 6 85.7% Tipo 158, Tipo 159 Alfa Romeo

Most consecutive wins

edit
Rank Manufacturer Wins Season(s) Races Engine(s) Winning team(s)
1 Ford 22 1972, 1973, 1974 1972 Austrian Grand Prix – 1974 South African Grand Prix DFV Lotus, Tyrrell, McLaren, Brabham
2 Ford 20 1968, 1969, 1970 1968 British Grand Prix – 1970 Monaco Grand Prix DFV Lotus, Matra, McLaren, Brabham, March
3 Renault 16 1995, 1996 1995 French Grand Prix – 1996 San Marino Grand Prix RS7, RS8 Benetton, Williams
4 Honda RBPT 14 2023 2023 Bahrain Grand Prix – 2023 Italian Grand Prix RBPTH001 Red Bull
5 Honda 11 1988 1988 Brazilian Grand Prix – 1988 Belgian Grand Prix RA168E McLaren
6 Ferrari 10 2002 2002 Canadian Grand Prix – 2002 Japanese Grand Prix Tipo 051 Ferrari
Mercedes 2015, 2016 2015 Japanese Grand Prix – 2016 Russian Grand Prix PU106B Hybrid, PU106C Hybrid Mercedes
2016 2016 Monaco Grand Prix – 2016 Singapore Grand Prix PU106C Hybrid Mercedes
2018, 2019 2018 Brazilian Grand Prix – 2019 French Grand Prix M09 EQ Power+, M10 EQ Power+ Mercedes
10 Ford 9 1980, 1981 1980 Dutch Grand Prix – 1981 Belgian Grand Prix DFV Brabham, Williams
Renault 2013 2013 Belgian Grand Prix – 2013 Brazilian Grand Prix RS27-2013 Red Bull
Red Bull Powertrains 2022 2022 French Grand Prix – 2022 Mexico City Grand Prix RBPTH001 Red Bull
Honda RBPT 2023, 2024 2023 Japanese Grand Prix – 2024 Saudi Arabian Grand Prix RBPTH001, RBPTH002 Red Bull

See also

edit

Notes

edit
  1. ^ Organized and run by Association Internationale des Automobile Clubs Reconnus (AIACR), the forerunner to the FIA, from 1931 to 1939.
  1. ^ Built by Ilmor between 1994 and 2005
  2. ^ Built by Cosworth. Cosworth was supported by Ford for many years (which even owned Cosworth outright from 1998 to 2004), and many of the Cosworth designs – from 1966 to 2004 – were owned by Ford and specifically named as Ford engines (contrary to the sometimes seen Ford-Cosworth or Ford/Cosworth vernacular) under various contracts.
  3. ^ a b Built by Honda
  4. ^ Built by Porsche
  5. ^ The Indianapolis 500 was part of the World Drivers' Championship from 1950 to 1960
  6. ^ Built by Renault
  7. ^ Built by Mercedes
  8. ^ a b From 1950 to 1960, the Indianapolis 500 was part of the World Drivers' Championship, though the Indianapolis 500 was held to AAA regulations rather than Formula One regulations. During those 11 years, only once did a regular Formula One driver enter an Indianapolis 500 race, when eventual 1952 Formula One World Drivers' Champion Alberto Ascari competed in the 1952 race, retiring on lap 40 of 200.[97] Thus, Alfa Romeo did not attempt to achieve a 100% sweep in 1950, and Ferrari failed in its attempt to complete the sweep in 1952.

References

edit
  1. ^ "F1 Engine rule change through the years". www.formula1-dictionary.net. Archived from the original on 11 November 2020. Retrieved 10 November 2020.
  2. ^ "Formula 1 Engine". www.formula1-dictionary.net. Archived from the original on 12 November 2020. Retrieved 10 November 2020.
  3. ^ "McLaren Racing - History of the F1 engine". Retrieved 10 November 2020.
  4. ^ Fédération Internationale de l’Automobile (23 January 2014). "2014 FORMULA ONE TECHNICAL REGULATIONS" (PDF). Archived (PDF) from the original on 27 March 2014. Retrieved 27 February 2014.
  5. ^ Engine / gearbox Archived 22 February 2014 at the Wayback Machine Understanding the Sport, Official Formula 1 Website
  6. ^ Scarborough, Craig. "Technically Challenged: Renault Innovations in Formula One" (PDF). Atlas F1. ScarbsF1.com. Archived (PDF) from the original on 24 August 2009. Retrieved 4 June 2012.
  7. ^ a b Taulbut, Derek. "Note 89 – TurboCharging background" (PDF). Grand Prix Engine Development 1906 – 2000. Grandprixengines.co.uk. Archived (PDF) from the original on 3 July 2012. Retrieved 4 June 2012.
  8. ^ "F1 Hockenheim 2006 Q2 - Mark Webber Onboard Lap". 7 July 2011. Archived from the original on 18 December 2015. Retrieved 4 January 2015 – via www.youtube.com.
  9. ^ "Cosworth V8 at 20,000rpm". 3 July 2007. Archived from the original on 28 November 2014. Retrieved 4 January 2015 – via www.youtube.com.
  10. ^ "Renault R26". 30 April 2009. Retrieved 27 November 2014.
  11. ^ "Profile – Renault R26". 7 July 2014. Retrieved 25 January 2015.
  12. ^ "Why do big diesel engines and race car engines have such different horsepower ratings?". HowStuffWorks. 16 May 2000. Archived from the original on 29 March 2014. Retrieved 2 April 2014.
  13. ^ Abidin, Zainal; Hoag, Kevin; Badain, Nicholas (October 2021). "Dilute Combustion Assessment in Large Bore, Low Speed Engines". SAE Technical Paper Series. Vol. 1. doi:10.4271/2017-01-0580. Archived from the original on 27 October 2021. Retrieved 12 October 2021.
  14. ^ a b c d Honda Motor Co. "F1 Powertrain Combustion Efficiency". Retrieved 1 October 2024.
  15. ^ F1 Engine Power Secrets Archived 29 November 2005 at the Wayback Machine, Ian Bamsey, June 2000 RACER magazine
  16. ^ Honda Motor Co. "MGU-H". Retrieved 10 September 2024.
  17. ^ Honda Motor Co. "MGU-H". Retrieved 10 September 2024.
  18. ^ Honda Motor Co. "MGU-K". Retrieved 10 September 2024.
  19. ^ "The RA521H". Retrieved 13 September 2024.
  20. ^ Honda Motor Co. "Progression of F1 V6 engines - 2015 to 2022". Retrieved 1 October 2024.
  21. ^ Tripathi, Gunaditya. "F1 boss confirms 2026 engine regulations to bring back much-awaited louder engine noise". Retrieved 22 September 2024.
  22. ^ Leo Breevoort; Dan Moakes; Mattijs Diepraam (22 February 2007). "World Championship Grand Prix engine designations and configurations". 6th Gear. Archived from the original on 24 February 2007. Retrieved 19 May 2007.
  23. ^ "Daimler "Phoenix" 12 hp racing car, 1899". Retrieved 26 September 2024.
  24. ^ Gascoigne, Roger (13 September 2023). "When Formula 2 ruled the world". Formula Scout. Retrieved 26 September 2024.
  25. ^ "The beginner's guide to the F1 Drivers' Championship". Retrieved 26 September 2024.
  26. ^ "The beginner's guide to the F1 Constructors' Championship". Retrieved 26 September 2024.
  27. ^ "8W - What? - Eagle Gurney-Weslake". 8w.forix.com. Archived from the original on 26 October 2021. Retrieved 15 November 2021.
  28. ^ "How A Formula 1 Internal Combustion Engine Works". f1chronicle.com. 26 August 2019. Archived from the original on 22 September 2020. Retrieved 21 September 2020.
  29. ^ "STATS F1 Engines". StatsF1. Archived from the original on 31 August 2010. Retrieved 9 September 2010.
  30. ^ Remi Humbert. "BMW Turbo F1 Engine". Gurneyflap. Archived from the original on 8 June 2007. Retrieved 19 May 2007.
  31. ^ "Honda Racing Gallery F1 第二期 McLaren Honda MP4/4". Honda公式ホームページ (in Japanese). Archived from the original on 27 June 2021. Retrieved 22 June 2021.
  32. ^ "Ferrari F1-8788C (1988)". www.ferrari.com. Archived from the original on 24 June 2021. Retrieved 22 June 2021.
  33. ^ "Engine Ford Cosworth • STATS F1". www.statsf1.com. Archived from the original on 28 June 2021. Retrieved 22 June 2021.
  34. ^ "Engine Judd • STATS F1". www.statsf1.com. Archived from the original on 27 June 2021. Retrieved 22 June 2021.
  35. ^ Engineering, Racecar (25 June 2020). "Natural Aspirations". Archived from the original on 14 November 2021. Retrieved 14 November 2021.
  36. ^ "3rd Naturally Aspirated Era" (PDF). Archived (PDF) from the original on 15 November 2021. Retrieved 15 November 2021.
  37. ^ "Engine Ford Cosworth • STATS F1". Archived from the original on 15 April 2021. Retrieved 30 April 2021.
  38. ^ "Ferrari's Most Alluring F1 Engines". June 2017. Archived from the original on 15 May 2021. Retrieved 30 May 2021.
  39. ^ "A Genius Named Todt". Atlasf1.autosport.com. Archived from the original on 30 March 2012. Retrieved 13 February 2011.
  40. ^ "3rd Naturally Aspirated Era Part 2" (PDF). Archived (PDF) from the original on 31 July 2021. Retrieved 31 August 2021.
  41. ^ "Engine Renault • STATS F1". www.statsf1.com. Archived from the original on 13 February 2021. Retrieved 24 February 2021.
  42. ^ "For Sale: A Ferrari 3000 (044/1) V12 Formula 1 Engine". 16 January 2021. Archived from the original on 15 June 2021. Retrieved 3 March 2022.
  43. ^ "McLaren Racing - Heritage - MP4-12". www.mclaren.com. Archived from the original on 29 November 2020. Retrieved 19 November 2020.
  44. ^ "Ferrari F310: Ferrari History". www.ferrari.com. Archived from the original on 14 November 2021. Retrieved 12 December 2021.
  45. ^ "WORLD MOTOR SPORT COUNCIL MEETING – JANUARY 15, 2000" (PDF). www.fia.com. 15 January 2000. Archived from the original (PDF) on 3 June 2011. Retrieved 24 January 2016.
  46. ^ "Williams FW22". www.f1technical.net. Archived from the original on 16 November 2020. Retrieved 19 November 2020.
  47. ^ "Williams F1 – BMW P84/85 Engine". F1network.net. Archived from the original on 22 November 2010. Retrieved 13 February 2011.
  48. ^ Roy McNeill (22 September 2003). "BMW World – Picture of the Week". Usautoparts.net. Archived from the original on 19 December 2007. Retrieved 17 October 2007.
  49. ^ "One of the greatest engines in history of Formula 1: BMW V10". 25 July 2015. Retrieved 9 November 2020.
  50. ^ Jaynes, Nick (16 July 2015). "BMW Engines in Formula 1's V10 Era". Road & Track. Archived from the original on 11 November 2020. Retrieved 2 April 2021.
  51. ^ 2005 Formula One technical regulations Archived 21 June 2006 at the Wayback Machine. FIA
  52. ^ "Bore and stroke on early 2000,s V10 engines - F1technical.net". www.f1technical.net. Archived from the original on 10 October 2021. Retrieved 10 October 2021.
  53. ^ "Honda R&D Technical Review F1 Special (The Third Era Activities)". Honda R&D Research Paper website. Archived from the original on 12 November 2020. Retrieved 10 November 2020.
  54. ^ "Cosworth story". www.formula1-dictionary.net. Archived from the original on 18 November 2020. Retrieved 16 November 2020.
  55. ^ "10 Years of BMW F1 Engines" (PDF). Archived (PDF) from the original on 14 April 2016. Retrieved 15 April 2016.
  56. ^ "Formula 1's 5 Most Iconic Engines ever". 26 February 2021. Archived from the original on 4 July 2022. Retrieved 28 February 2022.
  57. ^ "Toyota RVX-V10 F1 Engine". 13 July 2009. Archived from the original on 24 April 2021. Retrieved 30 May 2021.
  58. ^ "Toyota TF105B - F1technical.net". www.f1technical.net. Archived from the original on 2 June 2021. Retrieved 30 May 2021.
  59. ^ Henry, Alan, ed. (2006). AUTOCOURSE 2006–2007. Crash Media Group. pp. 82–83. ISBN 1-905334-15-X.
  60. ^ "King of Speed: Cosworth's CA 2.4l V8". www.f1technical.net. 15 October 2013. Archived from the original on 28 January 2021. Retrieved 1 April 2021.
  61. ^ 2006 Formula One technical regulations Archived 1 September 2006 at the Wayback Machine, chapter five, 15 December 2005
  62. ^ F1 technical, Toyota TF106 Specification Archived 30 January 2009 at the Wayback Machine, 14 January 2006
  63. ^ "Current Engine Ranking??? - Racing Comments Archive". The Autosport Forums. Archived from the original on 18 January 2021. Retrieved 19 November 2020.
  64. ^ "F1 News: FIA agrees to engine re-equalisation". Autosport.com. Haymarket Publications. 22 September 2009. Archived from the original on 24 September 2009. Retrieved 22 September 2009.
  65. ^ "Are there enough engines in F1 in 2010?". Grandprix.com. Inside F1. Archived from the original on 15 October 2012. Retrieved 2 June 2011.
  66. ^ "The basics of F1 KERS". 14 April 2009. Retrieved 14 April 2010.
  67. ^ "F1 2013: The last of the V8's". 11 October 2013. Archived from the original on 11 November 2020. Retrieved 24 February 2021.
  68. ^ "F1: Take a look at what's inside a Formula 1 engine". Car News, Auto123. 12 March 2010. Retrieved 28 March 2010.
  69. ^ "FIA Formula One World Championship Power Unit Regulations". FIA. 29 June 2011. Archived from the original on 8 December 2011. Retrieved 30 November 2011.
  70. ^ a b Allen, James (20 April 2011). "F1 set for electric only in the pit lane?". JamesallenonF1.com. Archived from the original on 23 June 2011. Retrieved 2 June 2011.
  71. ^ "Teams are keeping revs under 12000 rpm". Archived from the original on 16 October 2014. Retrieved 11 October 2014.
  72. ^ Haupt, Andreas (30 July 2019). "Motorleistung der Formel 1 (2019): Renault erreicht die 1.000 PS". auto motor und sport. Archived from the original on 28 January 2021. Retrieved 11 December 2020.
  73. ^ "Red Bull To Take On Honda F1 Power Unit Technology From 2022". Red Bull. Archived from the original on 1 March 2021. Retrieved 16 March 2021.
  74. ^ "Formula 1's 2021 regulations: What's new for 2021?". Autosport.com. 15 January 2021. Archived from the original on 13 September 2021. Retrieved 13 September 2021.
  75. ^ a b "Formula 1 unveils 2021 engine plans". speedcafe.com. 1 November 2017. Archived from the original on 7 November 2017. Retrieved 8 September 2020.
  76. ^ a b "F1 2021: Liberty's 4WD, Porsche & Spec PU's". thejudge13.com. 8 May 2018. Archived from the original on 27 September 2020. Retrieved 8 September 2020.
  77. ^ Noble, Jonathan (26 October 2017). "Analysis: Why 4WD is on Formula 1's agenda". motorsport.com. Archived from the original on 11 November 2020. Retrieved 8 September 2020.
  78. ^ Jamie Woodhouse (28 February 2022). "All the major changes for the F1 2022 season". Retrieved 28 February 2023.
  79. ^ Cooper, Adam (10 July 2018). "F1 manufacturers push back on 2021 engine proposals". Retrieved 10 July 2019.
  80. ^ "F1's 2026 power unit regulations approved by FIA's World Motor Sport Council · RaceFans". 16 August 2022. Retrieved 16 August 2023.
  81. ^ "7 things you need to know about the 2026 F1 engine regulations". www.formula1.com. 16 August 2022. Retrieved 4 April 2024.
  82. ^ "Audi to join Formula 1 from 2026". www.formula1.com. Retrieved 26 August 2022.
  83. ^ "Ford announce plans to return to F1 from the 2026 season". Formula 1.Com. 3 February 2023. Retrieved 3 February 2024.
  84. ^ "Ford announce new technical partnership with Red Bull for 2026 and beyond". Formula 1.Com. 3 February 2023. Retrieved 20 February 2023.
  85. ^ "BREAKING: Ford to partner with Red Bull for the 2026 season and beyond". Formula 1 Twitter. Retrieved 20 April 2023.
  86. ^ Cooper, Sam (3 February 2023). "FIA confirm six engine suppliers, including Honda and Ford, signed up for F1 2026". PlanetF1. Retrieved 3 February 2023.
  87. ^ "FIA Confirms 2026 Formula 1 Power Unit Supplier Registrations". Federation Internationale de l'Automobile. 3 February 2023. Retrieved 20 April 2023.
  88. ^ https://www.the-race.com/formula-1/renault-to-stop-f1-engine-programme-after-2025-mercedes-switch/
  89. ^ "How Long do F1 Engines Last?". F1 Chronicle. 17 June 2020. Archived from the original on 25 April 2021. Retrieved 25 April 2021.
  90. ^ "F1 rules and stats 1960–1969". 1 January 2009. Archived from the original on 12 August 2014. Retrieved 9 August 2014.
  91. ^ "2006 Formula One Technical Regulations". Archived from the original on 11 November 2020. Retrieved 10 November 2020.
  92. ^ "How Formula One's Amazing New Hybrid Turbo Engine Works". 22 January 2014. Archived from the original on 14 August 2014. Retrieved 9 August 2014.
  93. ^ Fédération Internationale de l’Automobile (23 January 2014). "2014 FORMULA ONE TECHNICAL REGULATIONS" (PDF). Article 5.1 on p.21. Archived (PDF) from the original on 27 March 2014. Retrieved 12 August 2014.
  94. ^ Fédération Internationale de l’Automobile. "2022 FORMULA ONE TECHNICAL REGULATIONS" (PDF). Archived (PDF) from the original on 1 May 2020. Retrieved 28 April 2020.
  95. ^ Honda Motor Co. "Formula 1 Carbon Neutral Fuel". Retrieved 1 October 2024.
  96. ^ "Spicer Horsepower and Torque Calculator". Retrieved 1 August 2024.
  97. ^ "F1: A brief history of the US Grand Prix". F1.com. 14 November 2012. Archived from the original on 21 October 2018. Retrieved 20 October 2018 – via Racing News.
edit
 
Wikimedia Commons has media related to Formula One engine.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Formula_One_engines&oldid=1256528188"