End-of-train device

(Redirected from Flashing rear end device)

The end of train device (ETD), sometimes referred to as an EOT, flashing rear-end device (FRED) or sense and braking unit (SBU) is an electronic device mounted on the end of freight trains in replacement of a caboose. They are divided into three categories: "dumb" units, which only provide a visible indication of the rear of the train with a flashing red taillight; "average intelligence" units with a brake pipe pressure gauge; and "smart" units, which send back data to the crew in the locomotive via radio-based telemetry.[1] They originated in North America, and are also used elsewhere in the world, where they may include complete End of Train Air System (ETAS) or Sense and Brake Unit (SBU) devices.[2][3]

An ETD on a container train in 2005

Tail lamps

edit
 
Introduced as long ago as the days of the Liverpool and Manchester Railway in the 1830s, tail lamps are an integral part of railway safety. This traditional lamp has been attached by the guard to the rear of the train for Broomhill railway station at Aviemore railway station.

The earliest known method of showing the position of and completeness of a train was by the Stockton and Darlington Railway in the 1830s. These early references are to the use of a burning brazier on the rear of the locomotive. It is easy to imagine that the danger represented by this was as significant as the risks it was trying to counter.[4]

The Liverpool and Manchester Railway were the first to codify the requirement for a tail Lamp in their 1840 Rules and Regulations that a red tail Lamp must be carried on each train. The purpose of this was for signallers working under the absolute block system to ensure that trains were complete when passing their signal box.

Such lamps were required to be carried by the rear coach of passenger trains and, for freight trains, the brake van (caboose) until their abolition (subsequently, the rear freight wagon must carry such a lamp). Locomotives and multiple units must also display a red light at the rear, however this is usually achieved by a lamp or light built into the train.

End of train devices

edit

Design and use

edit

A "dumb" ETD can be as simple as a red flag attached to the coupler on the last car of the train, whereas "smart" devices monitor functions such as brake line pressure and accidental separation of the train using a motion sensor, functions that were previously monitored by a crew in the caboose.[1] The ETD transmits data via a telemetry link to the Head-of-Train Device (HTD) in the locomotive, known colloquially among railroaders as a "Wilma,"[where?] after cartoon character Wilma Flintstone. In Canada, this device is known as a sense and braking unit (SBU).

A typical HTD contains several lights indicating telemetry status and rear end movement, along with a digital readout of the brake line pressure from the ETD. It also contains a toggle switch used to initiate an emergency brake application from the rear end. In modern locomotives, the HTD is built into the locomotive's computer system, and the information is displayed on the engineer's computer screen.

Railroads have strict government-approved air brake testing procedures for various circumstances when assembling trains or switching out cars en route. After a cut is made between cars in a train and the train is rejoined, in addition to other tests, the crew must verify that the brakes apply and release on the rear car (to ensure that all of the brake hoses are connected and the angle cocks, or valves, are opened). In most cases, the engineer is able to use information from the ETD to verify that the air pressure reduces and increases at the rear of the train accordingly, indicating proper brake pipe continuity. This device is said to constitute a fail-safe condition.


The DPS ETD reduced labor costs, as well as the costs of the purchase and upkeep of cabooses. The Brotherhood of Conductors and Brotherhood of Railroad Brakemen were also greatly affected by ETD, as this electronic unit replaced two crewmen per train. The widespread use of ETDs has made the caboose nearly obsolete. Some roads still use cabooses where the train must be backed up, on short local runs,[1] as rolling offices, or railroad police stations and as transportation for right-of-way maintenance crews. In some cases (see photo) instead of hitching a caboose, an employee stands on the last car when the train is backing up.

Evolution

edit

The first ETD use is attributed to Florida East Coast Railway in 1968, soon after which other Class I railroads began using ETDs as well. By the mid-1980s they were common equipment.[1] Early models were little more than a brake line connection / termination, a battery and flashing tail light. As their use became more widespread through the 1980s, ETDs were equipped with radio telemetry transmitters to send brake pressure data to a receiver in the locomotive. To reduce the cost of battery replacements, ambient light sensors were added so the flashing light on the ETD would illuminate only during dusk and after dark. Later models have a small turbine-powered electrical generator using air pressure from the brake line to power the ETD's radio and sensors.

The one-way communication of brake data from the ETD to the locomotive evolved into two-way communication that enables the engineer to apply the brakes from both ends of the train simultaneously in an emergency.[1] This is useful in the event that a blockage (or an unopened valve) in the train's brake line is preventing dumping the air pressure and causing all of the brakes in the train going into an emergency application. Such a situation could be dangerous, as stopping distance increases with fewer functioning brakes. Dumping the brake line pressure from both the front and rear of the train simultaneously ensures that the entire train applies all of its brakes in emergency. Other electronics within the ETD were also enhanced, and many now include GPS receivers as well as the two-way radio communications.

Last vehicle board

edit

Last vehicle board, often abbreviated as LV board, is a signaling board used on trains in some countries.

In India

edit
 
Last vehicle sign at the back of an Indian train

The last vehicle of a train is supposed to carry a red lamp at the rear. Earlier, the requirement was for merely an oil lamp, which was often missing or very feeble. In recent years provision of an electric lamp, as mandated by the rules, has become more common.

Last vehicle indications are of different types. A large 'X' is often seen painted on the rear of the coach that is the last one. A set of concentric circles may also be seen, although this seems to be going out of use as of 2008. EMU/DMU rakes have a smaller painted 'X' (red on white) at the rear, or sometimes a series of diagonal strokes painted on; these painted symbols are all in addition to the lamp mentioned above. In addition, a small board with the letters 'LV' (Last Vehicle, painted black on yellow) is often attached to the rear of the vehicle.

If a train passes by a station or signal cabin without the appropriate last vehicle indication (or without confirmation of the number of coaches or wagons), it is assumed that the train has separated and suitable emergency procedures are brought into play.

There are some cases where a last vehicle indication is not required — for instance, when the number of coaches or wagons in a train can be passed on to each block section after verification from the previous block section at the time the line clear indication is obtained (and with exchange of private numbers). The information is also provided to the section controllers. In some cases when working entirely within one block section, an 'LV' sign is not needed if the number of coaches or wagons is communicated by telephone to the next station.

In Sri Lanka

edit
 
In Sri Lanka red lights of DMUs shows the back end.

The Last Vehicle (LV) board is also used by Sri Lanka Railways. This board is used for same purpose and is usually hung in a buffer of the last carriage. However, in DMUs, to indicate the last carriage (usually a driving/trailer car) red lights are used.

See also

edit

References

edit
  • Lustig, David (August 2006). "End-of-train devices keep on evolving in back". Trains. Vol. 66, no. 8. p. 18. ISSN 0041-0934.
  1. ^ a b c d e McGonigal, Robert S. (May 1, 2006). "End-of-Train Devices". Trains. Kalmbach Publishing. Retrieved 2010-05-27.
  2. ^ "Wongm's Rail Gallery - ETM devices". RailGallery.Wongm.com. Retrieved 2010-05-27.
  3. ^ "VICSIG - Infrastructure - Safeworking in Victoria". VicSig.net. Retrieved 2010-05-27.
  4. ^ Horne, MAC (24 November 2019). British Railways Rule Books - a brief history and comentarty (PDF). Retrieved 25 June 2022.
edit