CGR 2nd Class 2-6-2TT

(Redirected from CGR 2nd Class 2-6-2TT 1875)

The Cape Government Railways 2nd Class 2-6-2TT of 1875 was a South African steam locomotive from the pre-Union era in the Cape of Good Hope.

CGR 2nd Class 2-6-2TT
CGR 2nd Class 2-6-2TT no. M26, with tender and "front porch railings", Fish River Bridge, c. 1881
Type and origin
Power typeSteam
DesignerRobert Stephenson and Company
BuilderRobert Stephenson and Company
Avonside Engine Company
Kitson and Company
Serial numberRS 2205–2210, 2332–2339, 2353 (engines), RS 2215–2217, 2221–2223 (tenders)
Avonside 1110–1113, 1157–1158, 1193–1194, 1209–1210
Kitson 2038–2041
Build date1875–1879
Total produced29 (2 lost at sea)
Specifications
Configuration:
 • Whyte2-6-2TT (Prairie)
 • UIC1’C1’n2t
Driver2nd coupled axle
Gauge3 ft 6 in (1,067 mm) Cape gauge
Leading dia.24 in (610 mm)
Coupled dia.38 in (965 mm)
Trailing dia.24 in (610 mm)
Wheelbase:
 • Axle spacing
(Asymmetrical)
1–2: 4 ft 8 in (1,422 mm)
2–3: 3 ft 4 in (1,016 mm)
 • Engine20 ft 3 in (6,172 mm)
 • Coupled8 ft (2,438 mm)
Length:
 • Over couplers27 ft (8,230 mm)
Height12 ft (3,658 mm)
Frame typePlate
Axle load9 LT 6 cwt 3 qtr (9,487 kg) ​
 • Leading2 LT 9 cwt (2,489 kg)
 • 1st coupled7 LT 13 cwt (7,773 kg)
 • 2nd coupled9 LT 6 cwt 3 qtr (9,487 kg)
 • 3rd coupled6 LT 17 cwt 1 qtr (6,973 kg)
 • Trailing2 LT 9 cwt (2,489 kg)
Adhesive weight23 LT 17 cwt (24,230 kg)
Loco weight28 LT 14 cwt 4 qtr (29,210 kg)
Tender type2-axle
Fuel typeCoal
Fuel capacityEngine: 0 LT 15 cwt (0.8 t)
Tender: 2 LT (2.0 t)
Water cap.Engine: 650 imp gal (2,950 L)
Tender: 900 imp gal (4,090 L)
Firebox:
 • TypeRound-top
 • Grate area11 sq ft (1.0 m2)
Boiler:
 • Pitch5 ft 10+12 in (1,791 mm)
 • Tube plates10 ft (3,048 mm)
Boiler pressure130 psi (896 kPa)
Safety valveSalter
Heating surface:
 • Firebox58 sq ft (5.4 m2)
 • Tubes692 sq ft (64.3 m2)
 • Total surface750 sq ft (70 m2)
CylindersTwo
Cylinder size15 in (381 mm) bore
20 in (508 mm) stroke
Valve gearStephenson
Train brakesClarke's chain brakes
CouplersJohnston link-and-pin
Performance figures
Tractive effort11,546 lbf (51.36 kN) @ 75%
Career
OperatorsCape Government Railways
Class2nd Class
Number in class27
NumbersE17-E26, M5-M10, M25-M33, W1-W2
Delivered1875–1879
First run1875

The first mixed traffic locomotives to enter service on the new 3 feet 6 inches Cape gauge mainlines of the Cape Government Railways were 2-6-2 Prairie type side-tank engines which were delivered between 1875 and 1879. Four-wheeled tenders were also acquired and the locomotives could be operated in either a tank or tank-and-tender engine configuration, as circumstances demanded. These locomotives were later designated the Cape 2nd Class.[1][2]

Cape Government Railways

edit

In 1872, the Cape Government took over the operation of all railways in the Cape of Good Hope and established the Cape Government Railways (CGR). Shortly before, it had been decided to adopt the narrower 3 feet 6 inches gauge instead of the existing 4 feet 8½ inches broad gauge for all further railway expansions, since it would decrease the cost of construction through the difficult terrain which lay inland from the three major ports of the Cape of Good Hope at Cape Town, Port Elizabeth and East London. This narrower gauge is still known as Cape gauge.[1][3]

Since the operational area within the Colony was so vast, the CGR was divided into three semi-autonomous systems. The Eastern System was headquartered in East London, with A.E. Schmid as Chief Resident Engineer and J.D. Tilney as Locomotive Superintendent. The Midland System was headquartered in Port Elizabeth, with D. Jackson Scott as Chief Resident Engineer and Mr. Edwards as Locomotive Superintendent. The Western System was headquartered in Cape Town, with W.G. Brounger as Chief Resident Engineer as well as Consulting Engineer for the whole CGR, and Michael Stephens as Locomotive Superintendent.[3][4]

Manufacturers

edit

The first Cape gauge mainline locomotives to enter service on the CGR were delivered in 1875. An order for six 2-6-2T Prairie type locomotives was placed with Robert Stephenson and Company, followed by a separate order for six four-wheeled tenders. The Stephenson locomotives were numbered W1 and W2 for the Western system and M7 to M10 for the Midland System.[2]

At the same time, four more locomotives were ordered from the Avonside Engine Company. Two of the Avonside locomotives went to the Midland System, numbered M5 and M6. The other two were intended for the Eastern System, but they were lost at sea during delivery when the ship Memento sank off East London on 5 February 1876.[2]

These locomotives were followed by nineteen more, all with optional tenders, ordered from three manufacturers.

  • Four were delivered from Kitson and Company in 1876, numbered in the range from E17 to E20 for the Eastern system.
  • Four were delivered from Avonside Engine Company in 1876 and 1878, numbered in the range from E21 to E24 for the Eastern system.
  • Nine more were delivered from Robert Stephenson in 1878 and 1879, numbered in the range from M25 to M33 for the Midland system.
  • The last two were delivered from Avonside Engine Company in 1879, numbered E25 and E26 for the Eastern system, to replace the two which had been lost at sea.[2]

When a locomotive classification system was introduced by the CGR, these locomotives were designated 2nd Class.[1]

Characteristics

edit

Tenders

edit

While all the locomotives were delivered with four-wheeled tenders, they could be operated with or without the tenders, as circumstances demanded. In practice, they were used in the tank engine configuration while performing shunting or short-distance work, and in the tank-and-tender configuration when an increased coal and water supply was required during longer distance mainline work.[1][4]

Brakes

edit

The locomotives were equipped with Clarke's chain brakes. The braking system proved to be unsatisfactory, since breaking of the chain was not uncommon. In one instance this resulted in a bad accident with loss of life while a train was descending the Hex River rail pass.[1]

The chain brake was operated by a 58 inch (16 millimetres) link chain, which was carried on sheaves underneath the train along the centre, connected by coupling hooks between carriages or trucks. Under each vehicle, the chain hanged slack while not in use. It passed under two pulleys which were attached to pulling-rods to operate the wooden brake blocks. To operate the brakes, the chain could be tightened from either end of the train. The guard's van could be used to retard a train on down grades, or to stop the entire train. In the event of a broken or disconnected chain, however, the brake system was useless. By c. 1876, a simple vacuum brake system was introduced as a reserve brake.[4]

Service

edit

One of these locomotives is known to have been named, number W1 Byron. All of them were renumbered on occasions when the CGR altered its locomotive numbering systems c. 1886, 1888, 1890 and 1896.[1][2]

By 1904, only three of them were still in service, being employed on shunting and construction tasks. By 1912, when locomotive classification and renumbering was implemented on the newly established South African Railways, none of these 2nd Class locomotives were still in service.[2]

Works numbers and renumbering

edit

The builders, works numbers, years built, original numbers and known renumbering of the Cape 2nd Class of 1875 are listed in the table.[1][2]

Illustration

edit

The photographs illustrate the locomotive in various configurations.

References

edit
  1. ^ a b c d e f g Holland, D.F. (1971). Steam Locomotives of the South African Railways. Vol. 1: 1859–1910 (1st ed.). Newton Abbott, England: David & Charles. pp. 23–25. ISBN 978-0-7153-5382-0.
  2. ^ a b c d e f g C.G.R. Numbering Revised, Article by Dave Littley, SA Rail May–June 1993, pp. 94–95.
  3. ^ a b The South African Railways – Historical Survey. Editor George Hart, Publisher Bill Hart, Sponsored by Dorbyl Ltd., Published c. 1978, pp. 4, 8, 11.
  4. ^ a b c Espitalier, T.J.; Day, W.A.J. (1943). The Locomotive in South Africa – A Brief History of Railway Development. Chapter II – The Adoption of the 3 ft. 6 in. Gauge on the Cape Government Railways. South African Railways and Harbours Magazine, July 1943. pp. 515–518.