Ampère's force law

(Redirected from Ampere's force law)

In magnetostatics, the force of attraction or repulsion between two current-carrying wires (see first figure below) is often called Ampère's force law. The physical origin of this force is that each wire generates a magnetic field, following the Biot–Savart law, and the other wire experiences a magnetic force as a consequence, following the Lorentz force law.

Two current-carrying wires attract each other magnetically: The bottom wire has current I1, which creates magnetic field B1. The top wire carries a current I2 through the magnetic field B1, so (by the Lorentz force) the wire experiences a force F12. (Not shown is the simultaneous process where the top wire makes a magnetic field which results in a force on the bottom wire.)

Equation

edit

Special case: Two straight parallel wires

edit

The best-known and simplest example of Ampère's force law, which underlaid (before 20 May 2019[1]) the definition of the ampere, the SI unit of electric current, states that the magnetic force per unit length between two straight parallel conductors is

 

where   is the magnetic force constant from the Biot–Savart law,   is the total force on either wire per unit length of the shorter (the longer is approximated as infinitely long relative to the shorter),   is the distance between the two wires, and  ,   are the direct currents carried by the wires.

This is a good approximation if one wire is sufficiently longer than the other, so that it can be approximated as infinitely long, and if the distance between the wires is small compared to their lengths (so that the one infinite-wire approximation holds), but large compared to their diameters (so that they may also be approximated as infinitely thin lines). The value of   depends upon the system of units chosen, and the value of   decides how large the unit of current will be.

In the SI system,[2][3]   with   the magnetic constant, in SI units

μ0 = 1.25663706212(19)×10−6 H/m

General case

edit

The general formulation of the magnetic force for arbitrary geometries is based on iterated line integrals and combines the Biot–Savart law and Lorentz force in one equation as shown below.[4][5][6]

 

where

  •   is the total magnetic force felt by wire 1 due to wire 2 (usually measured in newtons),
  •   and   are the currents running through wires 1 and 2, respectively (usually measured in amperes),
  • The double line integration sums the force upon each element of wire 1 due to the magnetic field of each element of wire 2,
  •   and   are infinitesimal vectors associated with wire 1 and wire 2 respectively (usually measured in metres); see line integral for a detailed definition,
  • The vector   is the unit vector pointing from the differential element on wire 2 towards the differential element on wire 1, and |r| is the distance separating these elements,
  • The multiplication × is a vector cross product,
  • The sign of   is relative to the orientation   (for example, if   points in the direction of conventional current, then  ).

To determine the force between wires in a material medium, the magnetic constant is replaced by the actual permeability of the medium.

For the case of two separate closed wires, the law can be rewritten in the following equivalent way by expanding the vector triple product and applying Stokes' theorem:[7]  

In this form, it is immediately obvious that the force on wire 1 due to wire 2 is equal and opposite the force on wire 2 due to wire 1, in accordance with Newton's third law of motion.

Historical background

edit
 
Diagram of original Ampere experiment

The form of Ampere's force law commonly given was derived by James Clerk Maxwell in 1873 and is one of several expressions consistent with the original experiments of André-Marie Ampère and Carl Friedrich Gauss. The x-component of the force between two linear currents I and I', as depicted in the adjacent diagram, was given by Ampère in 1825 and Gauss in 1833 as follows:[8]

 

Following Ampère, a number of scientists, including Wilhelm Weber, Rudolf Clausius, Maxwell, Bernhard Riemann, Hermann Grassmann,[9] and Walther Ritz, developed this expression to find a fundamental expression of the force. Through differentiation, it can be shown that:

 

and also the identity:  

With these expressions, Ampère's force law can be expressed as:  

Using the identities:   and  

Ampère's results can be expressed in the form:  

As Maxwell noted, terms can be added to this expression, which are derivatives of a function Q(r) and, when integrated, cancel each other out. Thus, Maxwell gave "the most general form consistent with the experimental facts" for the force on ds arising from the action of ds':[10]  

Q is a function of r, according to Maxwell, which "cannot be determined, without assumptions of some kind, from experiments in which the active current forms a closed circuit." Taking the function Q(r) to be of the form:  

We obtain the general expression for the force exerted on ds by ds:  

Integrating around s' eliminates k and the original expression given by Ampère and Gauss is obtained. Thus, as far as the original Ampère experiments are concerned, the value of k has no significance. Ampère took k=−1; Gauss took k=+1, as did Grassmann and Clausius, although Clausius omitted the S component. In the non-ethereal electron theories, Weber took k=−1 and Riemann took k=+1. Ritz left k undetermined in his theory. If we take k = −1, we obtain the Ampère expression:  

If we take k=+1, we obtain  

Using the vector identity for the triple cross product, we may express this result as  

When integrated around ds' the second term is zero, and thus we find the form of Ampère's force law given by Maxwell:  

Derivation of parallel straight wire case from general formula

edit

Start from the general formula:   Assume wire 2 is along the x-axis, and wire 1 is at y=D, z=0, parallel to the x-axis. Let   be the x-coordinate of the differential element of wire 1 and wire 2, respectively. In other words, the differential element of wire 1 is at   and the differential element of wire 2 is at  . By properties of line integrals,   and  . Also,   and   Therefore, the integral is   Evaluating the cross-product:   Next, we integrate   from   to  :   If wire 1 is also infinite, the integral diverges, because the total attractive force between two infinite parallel wires is infinity. In fact, what we really want to know is the attractive force per unit length of wire 1. Therefore, assume wire 1 has a large but finite length  . Then the force vector felt by wire 1 is:   As expected, the force that the wire feels is proportional to its length. The force per unit length is:   The direction of the force is along the y-axis, representing wire 1 getting pulled towards wire 2 if the currents are parallel, as expected. The magnitude of the force per unit length agrees with the expression for   shown above.

Notable derivations

edit

Chronologically ordered:

  • Ampère's original 1823 derivation:
    • Assis, André Koch Torres; Chaib, J. P. M. C; Ampère, André-Marie (2015). Ampère's electrodynamics: analysis of the meaning and evolution of Ampère's force between current elements, together with a complete translation of his masterpiece: Theory of electrodynamic phenomena, uniquely deduced from experience (PDF). Montreal: Apeiron. ISBN 978-1-987980-03-5.
  • Maxwell's 1873 derivation:
  • Pierre Duhem's 1892 derivation:
  • Alfred O'Rahilly's 1938 derivation:

See also

edit

References and notes

edit
  1. ^ "26th CGPM Resolutions" (PDF). BIPM. Retrieved 1 August 2020.
  2. ^ Raymond A Serway & Jewett JW (2006). Serway's principles of physics: a calculus based text (Fourth ed.). Belmont, California: Thompson Brooks/Cole. p. 746. ISBN 0-534-49143-X.
  3. ^ Paul M. S. Monk (2004). Physical chemistry: understanding our chemical world. New York: Chichester: Wiley. p. 16. ISBN 0-471-49181-0.
  4. ^ The integrand of this expression appears in the official documentation regarding definition of the ampere BIPM SI Units brochure, 8th Edition, p. 105
  5. ^ Tai L. Chow (2006). Introduction to electromagnetic theory: a modern perspective. Boston: Jones and Bartlett. p. 153. ISBN 0-7637-3827-1.
  6. ^ Ampère's Force Law Scroll to section "Integral Equation" for formula.
  7. ^ Christodoulides, C. (1988). "Comparison of the Ampère and Biot–Savart magnetostatic force laws in their line-current-element forms". American Journal of Physics. 56 (4): 357–362. Bibcode:1988AmJPh..56..357C. doi:10.1119/1.15613.
  8. ^ O'Rahilly, Alfred (1965). Electromagnetic Theory. Dover. p. 104. (cf. Duhem, P. (1886). "Sur la loi d'Ampère". J. Phys. Theor. Appl. 5 (1): 26–29. doi:10.1051/jphystap:01886005002601. Retrieved 7 January 2015., which appears in Duhem, Pierre Maurice Marie (1891). Leçons sur l'électricité et le magnétisme. Vol. 3. Paris: Gauthier-Villars.)
  9. ^ Petsche, Hans-Joachim (2009). Hermann Graßmann : biography. Basel Boston: Birkhäuser. p. 39. ISBN 9783764388591.
  10. ^ Maxwell, James Clerk (1904). Treatise on Electricity and Magnetism. Oxford. p. 173.
edit